Video 1 — TOHNICHI STC3 series digital torque screwdriver, official demonstration (approx. 1 min 10 s; open in a new window / download)

The STC3 is TOHNICHI's digital torque screwdriver series for small-screw tightening and inspection. It packs a torque sensor, an angle encoder and a judgement circuit into one handheld screwdriver: torque and rotation angle are shown in real time during tightening, and a pass/fail verdict is issued directly against preset upper and lower limits. On assembly lines dominated by M1.6–M3 screws — notebooks, phones, appliance control boards, automotive interior trim — it takes over work that previously required three separate things: a torque wrench, a torque tester and a written record.

This article is based on the manufacturer's published specifications and the official demonstration video. It answers three questions: what the STC3 actually measures, how to choose between the three ranges, and how the standard and Bluetooth models differ. Every figure is taken from the official specification table — nothing has been extrapolated or filled in.

The video at the top of this page runs about 1 min 10 s and shows, in order: the body and the OLED screen, the target window, the ring indicator tracking torque and angle together, an actual small-screw tightening, the state of the LED ring, and the Bluetooth path that pushes data to a mobile device and then into a spreadsheet on a PC. The source file was AV1-encoded; it has been transcoded here to H.264 / AAC for web playback, with seek support.

1. Where the STC3 sits in the torque-tool family

One common confusion is worth clearing up first: a torque screwdriver, a torque wrench and a torque tester are three different tools and cannot substitute for one another.

Typical use is therefore: the operator tightens to the specified torque at the workstation and keeps a pass/fail record; the tool's own calibration is carried out on a torque tester. These two steps must not be confused.

The series covers three ranges, each available in a standard and a Bluetooth version — six models in total. In the model code, CN3 denotes the third-generation cN·m-based platform, G is the series designator, and the -BT suffix identifies the Bluetooth model.

2. Why torque and angle have to be measured together

Measuring torque alone leaves an unavoidable blind spot: reaching the torque does not mean the thread is sound. Stripped threads, cross-threading, a screw that never actually engaged, a missing washer — any of these can let the torque value "pass" at the instant of tightening while the joint itself has no holding strength. Angle monitoring exists to close that gap.

From a fastening-engineering point of view, a complete tightening has two stages: snug and rotation. Torque starts to rise as the screw head seats against the workpiece, and from that point the rotation angle is roughly proportional to clamp force. Reading the torque and angle curves together is what separates "entering the plastic region normally" from "the thread has already failed and the angle is running away".

The angle channel of the STC3 is specified as: range 0–999°, graduation 1°, accuracy ±2°+1 digit (measured while rotating 90° at an angular velocity of 30–180°/s). That last condition is stated explicitly by the manufacturer — outside 30–180°/s the angle accuracy is no longer assessed against this figure. Hand tightening normally falls inside that band; driving the tool with an electric screwdriver is where it needs watching.

One further official function relates to angle: re-tightening detection. If a screw that has already been tightened receives torque again, the angle turns out abnormally small and torque climbs very quickly. That signature can be detected, so a repeated or false tightening is less likely to slip through inspection.

3. Panel and display: three-line OLED, three keys, LED ring

A square control module sits at the middle of the STC3 body. Its face is an OLED display, with three keys along the bottom edge: left arrow, POWER, and confirm (check mark). In the official demonstration video the screen is laid out roughly as follows:

The practical value of putting target, limits and live value on one screen is that nothing has to be memorised. On a line changeover the operator only has to confirm that the window on screen matches the work order, instead of recalling "how much this screw should take" — which also removes room for tightening by feel.

A ring of LEDs circles the body around the screen. According to the official specification, once upper and lower limits are set, the pass/fail result is indicated by buzzer and LED together — light and sound confirm the moment the target is reached, so the result is still readable by colour in a noisy workshop. The video also shows a blue light state used to indicate the Bluetooth connection.

One point to be clear about: the menu hierarchy and key combinations (how to enter the setting screen, how to change the limits) belong to the instruction manual. This article does not reproduce specific key sequences, to avoid drifting from different firmware versions. The setting logic itself matches most digital torque tools: enter settings → select the target → set the upper and lower limits → save.

4. Two measurement modes: tightening and inspection

The official specification lists two measurement modes, tightening mode and inspection mode — the key difference between the STC3 and earlier single-function digital screwdrivers.

Mode Purpose Reading behaviour
Tightening mode Drives the screw from loose to seated, recording peak torque and rotation angle along the way Records the peak of the whole tightening stroke, used to judge whether this assembly pass
Inspection mode Re-checks a screw that is already tightened, to confirm it reached the specified torque Focuses on the torque at the instant the fastener starts to turn, i.e. the torque needed to break static friction

The difference between the two modes is not just the interface — it is a different physical quantity. Tightening mode measures the peak reached when driving the screw home; inspection mode measures the break-away torque of an already-tightened fastener. Using the wrong mode has a direct consequence: reading a tightening with inspection mode keeps driving the screw further and reads high; conversely, using inspection mode at an assembly station never gives you the true tightening peak.

One practical note: in inspection mode the check movement should be gentle, and you stop as soon as a value appears. Repeatedly applying torque adds plastic deformation to the thread, so the reading falls each time — what you end up measuring is no longer the original state of the joint.

5. Pass/fail judgement and data logging

The judgement chain in the STC3 is "set the window → tighten → light and sound feedback → one record stored automatically". The relevant entries in the official specification:

At 1,000 records, and assuming 200–300 screws per shift on one line, that covers roughly three to five shifts; export promptly over USB Type-C or Bluetooth and the limit effectively disappears. What really deserves attention is how auto store and reset behaves: in continuous measurement the tool stores one record and resets the display after each judgement, with no key press from the operator. That raises the tempo, but it also means you cannot go back and read the previous result on screen — the data has to be exported before it can be traced.

Which is why the next section, on data output, matters more in practice than it might look.

6. Data output: USB Type-C serial and Bluetooth 5.1

The whole STC3 series comes with serial output over a USB Type-C compatible port. Note the wording: serial output. It runs a serial communication protocol, not USB-mass-storage file copying, so it needs host software or a serial terminal to receive the data. This is often misunderstood at the selection stage — before purchasing, confirm that your existing system can read a serial stream.

The Bluetooth models add a wireless channel on top of that, specified as follows:

Item Specification
Bluetooth version5.1
Protocol / profileGATT proprietary protocol / HOGP (HID over GATT Profile)
Wireless output power8 dBm
Communication distanceApprox. 10 m (depends on the radio environment and the connected device)
Continuous operating timeApprox. 50 h (Bluetooth model) / approx. 60 h (standard model)
Charging timeApprox. 4.5 h

HOGP is the part worth expanding. HOGP stands for HID over GATT: the tool presents itself to the host as a standard HID peripheral, the same class as a keyboard or mouse. In practice this means some systems and applications can see the STC3 as an input device and type the value straight into the cell where the cursor sits, with no dedicated driver. The official video demonstrates exactly this path — data from the screwdriver goes over Bluetooth to a mobile device and from there into a spreadsheet on a PC. Whether it really works driver-free depends on the host operating system and the software in use, so test it once on your own PC before purchasing.

The other channel, the proprietary GATT protocol, is intended for the manufacturer's own app or host software. It carries more complete data (angle, pass/fail result and other structured fields) but requires the matching software.

7. Body, power and bit interface

In its side-by-side body comparison the official video marks 35% smaller body, meaning this generation is about 35% smaller than the previous one (the exact basis for the comparison is the manufacturer's). On an assembly floor, size is not a cosmetic matter: small-screw stations are often cramped with the view obstructed, so a more compact body makes the bit easier to align and reduces fatigue during long holding.

All three ranges measure about 225 mm overall, and weigh about 229 g (STC50), 233 g (STC200) and 267 g (STC500). The larger the range, the heavier the internal sensor and shaft assembly — that follows from the structure, it is not a configuration difference.

Power comes from a dedicated Ni-MH battery pack, BP-8, one supplied with the tool, charging in about 4.5 h. Operating ambient temperature is 0–40 °C, non-condensing. Compared with lithium, Ni-MH tolerates overcharging, has a long cycle life and suits the rough workshop habit of topping up whenever convenient; the trade-off is slightly higher self-discharge, so after long storage charge it fully before use.

The bit interface is 6.35 HEX — the common 1/4-inch hex, so standard commercially available bits fit directly. Phillips, slotted, hex and Torx tips can all be swapped as needed, with no proprietary bit restriction. For high-mix, low-volume lines that is a practical advantage.

8. Choosing between the three ranges

Model cN·m kgf·cm lbf·in Graduation Weight Bluetooth model
STC50CN3-G 5–50 0.5–5 0.44–4.4 0.02 cN·m Approx. 229 g STC50CN3-G-BT
STC200CN3-G 20–200 2–20 2–17 0.1 cN·m Approx. 233 g STC200CN3-G-BT
STC500CN3-G 50–500 5–50 4.4–44 0.2 cN·m Approx. 267 g STC500CN3-G-BT

The first rule of selection is to keep the working point between one third and two thirds of the range. That is standard practice in torque measurement, for two reasons: relative accuracy degrades noticeably near the bottom of the range (especially below 20% F.S.), while working continuously against full scale risks overloading and fatiguing the sensor.

By that rule:

Accuracy has to be read in bands: the STC50 is ±2% from 5–10 cN·m and ±1% from 10–50 cN·m; the STC200 is ±2% from 20–40 cN·m and ±1% from 40–200 cN·m; the STC500 is ±2% from 50–100 cN·m and ±1% from 100–500 cN·m. All three ranges share the same structure — ±2% low band, ±1% high band. If the process demands ±1% across the whole working span, the working point has to be raised above the band boundary; looking at the range alone is not enough.

Standard or Bluetooth: if the station is fixed and data goes to an industrial PC over USB Type-C, the standard model is sufficient; if you need to measure while moving around, or push values straight to a tablet or phone, take the Bluetooth model. The two differ by 10 hours of runtime (60 h vs 50 h), which is what the Bluetooth module costs.

9. Specification quick reference (STC50CN3-G-BT)

Item Specification
Torque range5–50 cN·m / 0.5–5 kgf·cm / 0.44–4.4 lbf·in
Graduation0.02 cN·m / 0.002 kgf·cm / 0.002 lbf·in
Torque accuracy5–10 cN·m: ±2%; 10–50 cN·m: ±1%
Angle range / graduation0–999° / 1°
Angle accuracy±2°+1 digit (rotating 90° at 30–180°/s)
Measurement modesTightening mode / inspection mode
Data memory1,000 records (torque, angle, pass/fail result)
Pass/fail judgementBuzzer and LED indication when upper and lower limits are set
Other functionsRe-tightening detection / auto store and reset / auto power-off
Data outputUSB Type-C serial output / Bluetooth
Power / charging timeNi-MH battery pack BP-8 / approx. 4.5 h
Continuous operating timeApprox. 50 h (Bluetooth model); approx. 60 h (standard model)
Operating ambient temperature0–40 °C (non-condensing)
Overall length / weightApprox. 225 mm / approx. 229 g
Bit interface / standard accessory6.35 HEX (standard commercial bits can be used) / battery pack BP-8

Note: range, graduation and accuracy bands for the STC200CN3 and STC500CN3 are given in the comparison table of the previous section. The standard model has no Bluetooth-related entries (Bluetooth version, protocol, output power, communication distance); all other specifications are identical. Weights are the manufacturer's nominal values, which do not distinguish the Bluetooth variant.

10. Frequently asked questions

Q1: Can the STC3 be used as a torque wrench?
No. The maximum is 500 cN·m, i.e. 5 N·m, with a 6.35 mm hex bit interface — neither the structure nor the range suits bolts and nuts. Tightening a fastener beyond the range will damage the sensor directly.

Q2: Apart from Bluetooth, how do the standard and Bluetooth models differ?
According to the official specification, range, accuracy, angle channel, memory and judgement functions are identical. There are only three differences: the Bluetooth module itself, the resulting runtime (60 h → 50 h), and weight (not separately specified by the manufacturer). For stationary assembly with Type-C data export, the standard model is the better buy.

Q3: What does the "+1 digit" in the angle accuracy ±2°+1 digit mean?
It is one count of error in the last displayed digit — the quantisation error of the resolution. The angle graduation is 1°, so this term adds a further 1°. In practice it should be read as "±2° plus 1° of display quantisation", not as a plain ±2°.

Q4: Can the battery be replaced by the user?
It uses the dedicated BP-8 battery pack, a replaceable item, one supplied with the tool. Ordinary Ni-MH cells or lithium cells are not recommended as substitutes — the pack's dimensions, contacts and charge management are matched to the model.

Q5: Does it need periodic calibration?
Yes. Digital torque tools are measuring instruments, and accuracy drifts with use. The usual approach is to set the interval according to your own quality system (6 or 12 months is common) and send the tool for multi-point calibration on a torque tester with the appropriate accreditation. Between calibrations, check it against a standard fastener; if the deviation starts to widen, bring the calibration forward.

Q6: What if Bluetooth will not connect or the data does not refresh?
First confirm from the LED ring whether the tool is in pairing mode; then check the distance (nominally about 10 m, in practice dependent on the radio environment); if you are using an app that relies on the proprietary protocol, check that it is the version for this model. For HOGP, the tool has to be added as an input device in the host's Bluetooth settings, not searched for inside the app.

11. Sources and notes

Selection and supply: this site lists STC50CN3-G, STC200CN3-G and STC500CN3-G together with the corresponding -BT Bluetooth models, six models in total — see digital torque screwdrivers for the itemised specifications. If you are unsure which range fits, tell us the screw size, the target torque, the number of fastenings per day and whether records are required, and we can advise against the ranges and accuracy bands. You can also contact our engineers directly.

The manufacturer reserves the right to change specifications; parameters for supplied goods are those of the latest technical manual and the contract.