Application: dynamic in-line tension measurement of round materials (yarn, optical fibre, enamelled wire, metal wire, wire rope, stranded wire, carbon fibre, etc.). This series uses V-groove guide rollers and does not support flat materials such as flat belts, steel strips or PET strapping. Core selection principle: measurement accuracy is best when the actual tension falls within 20%~80% of the instrument's capacity.
1. Four key selection steps
Step 1 — Confirm the material type and estimated tension
Identify the material first and estimate the real tension on the production line; this determines the required capacity.
Step 2 — Confirm the maximum line speed
The maximum permissible line speed for the entire NT series is 1000m/min. The instrument is not suitable above this speed.
Step 3 — Choose the handle: standard hand-held / -F lever-assisted
- Small-capacity models (NT-100 ~ NT-10K): lightweight bodies with the standard hand-held handle; easy one-handed threading, suited to fine filaments and small-to-medium wire
- Large-capacity models (20daN and above: NT-20K-F / 30K-F / 50K-F / 50K-F-ST): thick material under high tension, with the -F lever-assisted handle that reduces the force needed to thread the wire, so one operator can handle heavy stranded cable
Step 4 — Choose the roller material: aluminium / -ST steel
- Normal conditions (smooth, burr-free, soft materials, ordinary wire rope): hard-anodised aluminium rollers (standard), light and economical
- High-wear conditions (hard steel wire, burry rope, continuous long-run production testing): -ST steel rollers for greater wear resistance and longer service life
2. NT series model comparison
| Model | Capacity | Resolution | Configuration | Recommended material |
|---|---|---|---|---|
| NT-100 | 0~100cN | 0.1cN | Standard handle, aluminium roller | Optical fibre, ultra-fine yarn, very fine chemical filament |
| NT-200 | 0~200cN | 0.1cN | Standard handle, aluminium roller | Fine yarn, fine polyester, micro enamelled wire |
| NT-500 | 0~500cN | 0.1cN | Standard handle, aluminium roller | Regular yarn, standard enamelled wire, fine copper wire |
| NT-1000 | 0~1000cN | 1cN | Standard handle, aluminium roller | Coarse enamelled wire, fine metal wire, continuous filament |
| NT-2000 | 0~2000cN | 1cN | Standard handle, aluminium roller | Fine steel wire, steel cord, fine wire rope |
| NT-5000 | 0~5000cN | 5cN | Standard handle, aluminium roller | Small and medium wire rope, fine stranded wire |
| NT-10K | 0.1~10daN | 0.1daN | Standard handle, aluminium roller | General multi-strand cable, medium stranded wire |
| NT-20K-F | 0.2~20daN | 0.1daN | Lever-assisted handle, aluminium roller | Heavy wire rope, light overhead stranded conductor |
| NT-30K-F | 0.3~30daN | 0.1daN | Lever-assisted handle, aluminium roller | Large-diameter wire rope, coarse carbon fibre |
| NT-50K-F | 0.5~50daN | 0.1daN | Lever-assisted handle, aluminium roller | Heavy multi-strand cable, smooth burr-free wire |
| NT-50K-F-ST | 0.5~50daN | 0.1daN | Lever-assisted handle, -ST steel roller | Hard steel wire, burry rope, high-wear continuous lines |
3. Quick recommendations by industry
- Textiles and chemical fibres (yarn, polyester, nylon, fibre)
- Ultra-fine fibre / optical fibre → NT-100
- General spinning, multifilament → NT-200 / NT-500
- Industrial continuous filament → NT-1000
- Electronic enamelled wire, fine copper and aluminium wire
- Micro enamelled wire → NT-200 / NT-500
- Coarse enamelled wire, fine metal wire → NT-1000
- Steel wire, steel cord, small and medium wire rope
- Steel cord, fine steel wire → NT-2000
- Small and medium wire rope → NT-5000 / NT-10K
- Wire rope, overhead conductors, prestressing strand, coarse carbon fibre
- General heavy cable → NT-20K-F / NT-30K-F
- High-tension smooth stranded wire → NT-50K-F
- Hard steel wire, burrs, long continuous testing → NT-50K-F-ST
4. Important selection notes
- ❗Never undersize the capacity: maximum working tension must not exceed 80% of full scale, or the sensor may be damaged by overload. An oversized capacity is also wrong — resolution suffers and accuracy drops.
- ❗Round cross-sections only. The V-groove rollers cannot be used with flat steel strip, flat rubber belts or strapping.
- ❗This is a dynamic running-line tension meter, intended primarily for moving material on a production line. For static tensile tests, use a force gauge instead.
- ✅ All models support wire-diameter compensation: entering the material diameter automatically corrects wrap-angle error and improves accuracy (10K models and above).
- ✅ Communication: USB / RS232 / WiFi are available as options on every model for PC data acquisition, report export and quality traceability.
- ✅ Environment: operating temperature 10~45℃, humidity ≤90% RH non-condensing. Humid or corrosive environments require additional protection.
5. Quick selection Q&A
Q: When should I choose the -F lever-assisted handle?
A: At capacities of 20daN and above, where the material is thick, tension is high and threading by hand is difficult.
Q: When is the ST suffix needed?
A: When the material surface is burry or hard, or the line runs 24 h continuously and roller wear resistance is critical — specify -ST steel rollers. For smooth materials, standard aluminium rollers are more economical.
Q: What if I don't know the actual tension?
A: Provide the material diameter, material type and line speed; we will estimate the maximum working tension and match it using the 20%~80% rule.