I. Overview and product positioning

The ZEF-100 is the 100 cN model in the SCHMIDT (Germany) ZEF series. The series is designed for low-tension (small tension) measurement, mainly for tension sampling and process monitoring in textiles and fine wire, measuring fibres, single yarns, sewing threads and fine metal wires.

According to the manufacturer, the ZEF series covers fibres up to 200 tex and copper wire of Ø0.16 mm. The handheld, lightweight body with a slender yarn guide and small-diameter V-groove rollers is particularly suited to confined spaces where a benchtop instrument cannot be installed, measuring materials while they are running.

Compared with a benchtop tension test rig, the ZEF-100 offers three core benefits: instant on-site readings, no need to fix the material path, and non-contact inline sampling of running material.

II. Measuring principle and construction

The ZEF-100 uses a strain gauge bridge as its sensing element. The material passes over three V-groove rollers in sequence; tension deflects the middle measuring roller slightly, the strain gauge bridge converts that deflection into an electrical signal, and digital circuitry converts it into a displayed tension value. The maximum permissible deflection of the measuring roller is 0.5 mm。

The signal chain has the following characteristics:

The rollers are V-groove rollers on ball bearings, with low rolling friction and low heat build-up at high speed, reducing friction damage to fine filaments and measurement drift. The yarn guide has a roller displacement mechanism that captures the material quickly without stopping the line. The housing is made of high-strength POM (polyoxymethylene) plastic, combining impact resistance with low weight.

III. Core specification table

Item Specification Note
Measuring range0.5 – 100.0 cNapprox. 0.5 – 100 g equivalent force
Resolution0.1 cNConversion 1 cN = 1.02 g = 0.01 N
Accuracy±1% FS ±1 digittypical ±0.5% FS
Over-rangeapprox. 10% FSNo accuracy guarantee in this band
Overload protection200% FSShort-term mechanical protection limit
Measuring head width43 mmYarn guide width, suited to confined spaces
Roller groove diameterØ 7.4 mmSmall-diameter V-groove rollers
Calibration materialPA Ø0.12 mmPolyamide monofilament, covering about 95% of applications
Temperature coefficient (gain)< ±0.01% FS/°CGain drift figure
Sampling rateinternal ≈1 kHz
output 250 Hz
250 readings/s; AVG/MIN/MAX at 2 Hz
A/D conversion12 bitDigital signal processing
Display refresh rate2 times/sScreen refresh interval
Measuring unitscN / g / N / lbUser switchable
Operating temperature10 – 45 °C—
Ambient humidity≤ 85% RHMaximum relative humidity
Power supplyLiPo lithium battery
approx. 25 h continuous use
approx. 3.5 h charging, USB AC adapter 100–240 V
Dimensions157 × 124 × 32 mmlength × width × height, TFT version
Net / gross weightapprox. 200 g / approx. 600 gincluding case and adapter
Auto power-offafter approx. 3 min idleAutomatic power-off protection
Housing materialPlastic (POM)High-strength plastic housing
Menu languagesEN / DE / ES / PT / FRFactory-set language selectable

FS = Full Scale. Range, accuracy, dimensions and other parameters follow the manufacturer's latest manual.

IV. Display and data processing

The ZEF-100 uses a colour backlit TFT display (128 × 160) with three display modes for different working situations:

1. Numeric display
A plain numeric reading, the simplest and most direct, suited to quick sampling and paced production-line work.
2. Numeric + live bar graph
A dynamic bar indicator shows at a glance where tension sits relative to the setpoint and which way it is moving.
3. Numeric + time–tension curve
Tension plotted against time for observing stability, running-in patterns and periodic disturbances.

The display supports rotation in 90° steps. Because the instrument is handheld and measurement posture varies constantly, a rotatable display keeps the reading facing the operator, avoiding head-turning or obstruction and noticeably improving reading efficiency.

For data processing, the instrument automatically records, within each measuring cycle, minimum (MIN), maximum (MAX), last reading, average (AVG) and standard deviation (STD Dev), allowing quick assessment of batch consistency.

V. Key functions in detail

5.1 Auto Zero-Setting

Using special position-sensor technology, the instrument can zero itself automatically in any measuring posture with no manual zeroing. This is one of the most practically important features of a handheld tension meter: the operator can hold it at any angle or orientation and read directly without repeated zeroing. Manual zeroing is a common source of reading error in handheld operation, and auto-zero removes that step entirely.

5.2 Adjustable electronic damping

The instrument applies digital filtering by moving average, with adjustable damping (15 damping levels available). When tension fluctuates continuously, moderately increasing damping markedly stabilises the reading; conversely, when measuring sudden tension changes or observing trends, reduce damping to preserve response speed. It is a trade-off between "stable and readable" and "fast response", chosen to suit on-site conditions.

5.3 MIN / MAX limit alarms

Users set their own MIN and MAX alarm thresholds. When a reading leaves the set range, the TFT screen gives a graphical indication. This makes the ZEF-100 not only a measuring tool but also an inline pass/fail judgement device, suited to incoming inspection and process gate checks.

5.4 Multiple units and multilingual menus

Measuring units support cN、g、N、lb switchable at will, making it easy to match process standards, drawing annotations or customer specifications in different countries (conversion basis: 1 cN = 1.02 g = 0.01 N). Menu languages are English, German, Spanish, Portuguese and French, suitable for multinational plants and export production lines.

VI. Roller options and applicable line speeds

The ZEF-100's V-groove rollers come in several materials and maximum line-speed ratings; choosing the wrong roller directly limits measurable line speed and may damage the material:

Order code Maximum line speed Roller material Application note
Standard900 m/minHard-anodised aluminiumDefault choice for standard configuration
Code K2000 m/minHardened aluminiumHigh-speed applications
Code T450 m/minBlack plastic (POM)Smooth, non-slip surface, specifically for elastane (Lycra) filaments
Code W450 m/minNickel-plated steelWear-resistant, for hard or coarse-denier materials

The manufacturer also offers ZEF-100-T preconfigured models — the T-code smooth plastic roller version — optimised for elastane filament measurement and available for direct selection.

VII. ZEF / ZED series selection comparison

The ZE series comprises two product lines, ZEF (slender rollers, confined spaces) and ZED (larger rollers, higher speed), covering 0.5 – 500 cN:

Model Range Resolution Measuring head width Calibration material
ZEF-500.5 – 50.0 cN0.1 cN43 mmPA Ø0.12 mm
ZEF-100 (the model in this article)0.5 – 100.0 cN0.1 cN43 mmPA Ø0.12 mm
ZEF-2001 – 200.0 cN0.1 cN43 mmPA Ø0.12 mm
ZED-2001 – 200.0 cN0.1 cN63 mmPA Ø0.20 mm
ZED-5001 – 500 cN0.1 cN63 mmPA Ø0.20 mm

Key selection criteria:

Models from the same series listed on this site: ZEF-50(0.5–50 cN)、ZEF-100(0.5–100 cN)、ZEF-200 (1–200 cN). For higher-range tension measurement of wire, yarn or copper filament, compare the same brand's DTS-1000 digital tension meter; for a large analogue dial display, compare DX2-1000 and DX2-2000。

VIII. Calibration, certificates and compliance

The ZEF-100 is factory calibrated to the SCHMIDT factory calibration procedure, using a Ø0.12 mm polyamide monofilament (PA monofilament) as standard calibration material. The manufacturer states that this calibration covers about 95% of real applications。

When the material under test differs significantly from the standard calibration material in diameter, stiffness or cross-sectional shape, systematic bias is introduced into the measurement. In that case we recommend custom calibration using the customer's actual material, which requires about 5 m of material sample. The instrument has 3 independent calibration material memory slots, so custom calibration parameters can be switched alongside cN, g, N and lb, enabling "one instrument, multiple materials, multiple units" on site.

Supplied and optional documents
Certificate of compliance to EN 10204 section 2.1Supplied as standard
EN 10204 inspection certificate 3.1 + calibration reportAvailable as an option
CE certification (EMC tested)Passed

IX. Typical applications

Textiles and spinning
Tension sampling of low-tension yarns such as fine yarn, nylon and elastane; with the T-code smooth plastic roller for Lycra elastic filaments. Especially suitable for checking tension inside spinning machines where installation space is tight.
Sewing and embroidery threads
Tension typically runs from a few cN to several tens of cN, closely matching the ZEF-100 range — its most typical application.
Fine metal wire and filament
Covers low-tension measurement down to Ø0.16 mm copper wire; nickel-plated steel rollers are available for better wear resistance.
Incoming inspection and process gates
Set process limits with the MIN/MAX alarm for a visual warning on breach, providing inline pass/fail judgement; together with an EN 10204 3.1 certificate this meets quality-system traceability requirements.

X. Operation and maintenance notes

  1. Range matching: estimate the tension band before measuring and confirm it falls within 0.5–100 cN. Continuous use near the upper limit sacrifices effective accuracy and raises overload risk.
  2. Avoid over-range: momentary over-range of about 10% FS carries no accuracy guarantee; the mechanical overload protection limit is 200% FS and must not be treated as a normal measuring range.
  3. Roller selection: above 900 m/min switch to K-code rollers; elastane and similar elastic filaments require T-code smooth plastic rollers, as metal rollers tend to slip and damage the fibre.
  4. Damping adjustment: raise the damping level when tension fluctuates heavily for a stable reading; lower it when observing dynamic response.
  5. Calibration for material differences: order custom calibration when the material differs substantially from PA monofilament, otherwise readings carry systematic bias.
  6. Environmental limits: operating temperature 10–45 °C, humidity not exceeding 85% RH. Exceeding these limits affects accuracy and component life.
  7. Battery management: approx. 25 h continuous use and approx. 3.5 h charging. The instrument shuts down after 3 minutes of inactivity; for long storage keep some charge and recharge periodically.
  8. Cleaning and protection: in fine-yarn applications lint and oil easily build up on rollers, causing slip and reading drift. Clean roller grooves periodically with a lint-free cloth, never with corrosive solvents; avoid drops and overload.

XI. Frequently asked questions

Q1: What are the ZEF-100's range and accuracy?
Range 0.5 – 100.0 cN, resolution 0.1 cN, accuracy ±1% FS ±1 digit (typical ±0.5% FS). FS means full scale. Conversion: 1 cN = 1.02 g = 0.01 N.
Q2: Why does handheld measurement need auto-zero?
Posture and grip angle differ every time with a handheld instrument, and the instrument's own weight plus grip force add to the sensor, shifting the reading baseline. The ZEF-100 uses a position sensor to zero automatically in any posture, removing this source of error and the manual zeroing step.
Q3: The tension reading keeps jumping — what can I do?
Check three things in order: 1) increase the electronic damping level; 2) inspect rollers for lint, oil or slip, and clean or replace them; 3) check whether the material wanders sideways on the rollers and increase incoming tension slightly if so. If the process itself fluctuates strongly, switch to the time–tension curve mode to see the pattern and distinguish an "instrument problem" from a "process problem".
Q4: ZEF-100 or ZEF-200?
Both have a 43 mm measuring head and the same calibration material; only the range differs. If normal measured tension regularly exceeds 60 cN, choose the ZEF-200; if you need more headroom or ranges above 200 cN, consider the ZED-200 (63 mm measuring head).
Q5: What should I watch when measuring elastane (Lycra) fibres?
The T-code black POM plastic roller (max. line speed 450 m/min) is mandatory. Its smooth surface and suitable friction coefficient will not cut or slip on elastic fibres the way metal rollers can. The preconfigured ZEF-100-T model can be ordered directly.
Q6: Can I still use the standard roller above 900 m/min?
No. The standard roller is rated for a maximum line speed of 900 m/min and is made of hard-anodised aluminium. High-speed applications require K-code rollers (up to 2000 m/min). Running above the rating causes roller slip and heat build-up, leading to measurement error and component wear.
Q7: Which units are available?
Four units switchable at will: cN (centinewton), g (gram-force), N (newton) and lb (pound-force), to suit different process standards and drawing annotations.
Q8: What documents are supplied? Can you provide a calibration report?
A certificate of compliance to EN 10204 section 2.1 is supplied as standard. For metrological traceability, an EN 10204 inspection certificate 3.1 with a matching calibration report is available as an option.

XII. Specification version notes

Important note:The ZE series exists in different display versions, and early LCD versions can still be found in circulating literature. In the table above, the colour TFT display, 250 Hz sampling, approx. 25 h runtime and 157 × 124 × 32 mm dimensions are taken from the colour TFT version in the manufacturer's technical manual.

If your unit is an early 3½-digit LCD version, its display specification, body width and battery arrangement (some use two AAA cells) differ from this article, while core figures such as range, accuracy, measuring principle and sampling principle remain the same. Supplied specifications follow the latest technical manual and the contract; the manufacturer reserves the right to change specifications.