IMADA HTGS-10N Torque Testers (Model HTGS-10N) is a Torque Testers supplied by Guangzhou Yunke Electronics Co., Ltd. IMADA HTGS-10N Torque Testers — Torque Testers · Yunke Electronics. Request a quotation and datasheet.
Brand: IMADA | Category: Torque Testers
Sales Inquiries: 15626018696 · 78403603@qq.com

| Model | HTGS-10N |
|---|---|
| Rated Capacity | 10 N·m(1000 N·cm) |
| Displayed Value | 10.00 N·m(1000 N·cm) |
| Resolution | 0.01 N·m(1 N·cm) |
| Kgf · Cm Level | 100.0 kgf·cm × 0.1 |
| Level | 88 lbf·in × 0.01 |
| Accuracy | ±0.5% F.S. ±1 digit |
| Measurement Type | Rotatable Torque Measurement, when Needle () and when Needle () Dual toward can Measure |
| Measuring Unit | N · m, N · cm, kgf · m, kgf · cm, lbf · in, ozf · in(six Type Unit switchable; 0.5N · m levels only N · cm, kgf · cm, lbf · in, ozf · in Available) |
| Sampling Rate | Maximum 2000 Data / s (can Output Continuous Data, Non- only Peak) |
| Display Screen | 4 digits with Unit EL(OLED) Display, Environment and Light Same Sample , supports Customisable / Display |
| Display Update Rate | 16 times / s |
| Measurement mode | Real-time Mode / Peak Hold Mode optional ( when Needle Peak, when Needle Peak Division Hold) |
| Judgment Function | Comparison Device OK / NG Judgment, +NG Alarm; Display can Rotation, No. can Rotation, Method not Same Direction Reading |
| Built-in Memory | 1000 points Measurement Data |
| When Functions | Zero Setting Setting when Device, Auto Power-off Setting when Device (Power Saving), Time Display |
| Other functions | (Dumping) Setting, Setting Setting, 8 Type Language Single (, , , in Text, , Large , , Day ) |
| Safe Overload | Approx. 200% F.S. |
| Overload Warning | Over Over Full Scale Approx. 110% F.S. when Indication and Alarm |
| Signal Output | USB, RS232C, Mitutoyo Digimatic, ±2VDC Analog Output (D / A), three class Comparison Output (-NG / OK / +NG), Overload Alarm |
| External Connection | SEND(Connection points Hold), Zero Setting digits, Peak ON / OFF Setting |
| Power Supply | built-in NiMH Rechargeable Battery + AC Adapter; Continuous operation Approx. 8 hours, Full Approx. 2 hours |
| Operating Environment | Temperature 0~40℃, Humidity 20~80% RH(non-condensing) |
| Dimensions | Display Part Approx. W75 × D34 × H187 mm; Sensor Approx. ø38 mm(0.5N / 2N / 5N Type Body Length 100 mm; 10N Type with ø24 mm , Total Height Approx. 190 mm); Test Shaft ø5.5 mm |
| Body Weight | Display Part (Main unit) Approx. 490 g |
| Standard Accessories | AC Adapter, Check Gauge, Driver Light Disk (incl. Force Logger Data Recording Software), USB Data Cable, Case, L Type Wrench, (only 10N · m Range with) |
| Notes | Main unit excluding Test Fixture (Accessories requires optional); two only 10N · m Range Supplied Included |
Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.
| Model | Rated capacity | Displayed Value | Resolution |
|---|---|---|---|
| HTGS-0.5N | 0.5 N·m(50 N·cm) | 50.00 N·cm | 0.01 N·cm |
| HTGS-2N | 2 N·m(200 N·cm) | 2.000 N·m | 0.001 N·m |
| HTGS-5N | 5 N·m(500 N·cm) | 5.000 N·m | 0.001 N·m |
| HTGS-10N | 10 N·m(1000 N·cm) | 10.00 N·m | 0.01 N·m |
| Model | Rated capacity | N.C.C. Test | Displayed Value | Resolution | kgf cmcm | British |
|---|---|---|---|---|---|---|
| HTGS-0.5N | 0.5 N·m | 50 N·cm | 50.00 N·cm(0.500 N·m) | 0.01 N·cm(0.001 N·m) | 5.000 kgf·cm × 0.001 | 70 ozf·in × 0.01 |
| HTGS-2N | 2 N·m | 200 N·cm | 2.000 N·m(200.0 N·cm) | 0.001 N·m(0.1 N·cm) | 20.00 kgf·cm × 0.01 | 18 lbf·in × 0.01 |
| HTGS-5N | 5 N·m | 500 N·cm | 5.000 N·m(500.0 N·cm) | 0.001 N·m(0.1 N·cm) | 50.00 kgf·cm × 0.01 | 44 lbf·in × 0.01 |
| HTGS-10N | 10 N·m | 1000 N·cm | 10.00 N·m(1000 N·cm) | 0.01 N·m(1 N·cm) | 100.0 kgf·cm × 0.1 | 88 lbf·in × 0.01 |
| Category | Optional |
|---|---|
| Test the clamp | TA-00 small lock-locking clamp (AA-00, 0.5 ~ 6.5mm), TA-01 quadrupled hands, TA-02 sprained heads, XOX Q X ZX Twirl A-03 large folder; non-fixed custom clips are also accepted |
| Sensor stationing | SHT-5N sensor frame, capable of fixed sensors horizontally or vertically, increasing repetition (10N·m mass not applicable) |
| Small workstation | DT-ST small workstation (for 2 / 5 N·m), DT-STL light workstation, small workstations (for 2 / 5 N·m), DT-STL light workstations, workstations (for )/Stight workstations,/Stight workstations, etc.)/Stand shop DT-STLW light-broad-form working table (0.5 / 2 N·m for ZQ8 100mm). Reference: 10 |
| Other accessories | HT-9. 5 SQ cylinder holder, HT-DC series pin clip, HT-DBH/ HT-DBH-P torque, M10 to switch, XZ , M10 to ZX, P-308 replacement battery. Reference values: 9.5. |
| Software and Transfer | *The following are the most recent: Cable extensions (CB-108 / 208 / 308 / 808 / 908) / 908) /S / 908 / 908. Reference: DP-1VA, WL01, 2000Hz |
| Calibration | Additional calibration certificates (other fees) |
Q: What's the difference between HTGS and HTGA? Q: Q: Q
A: The accuracy of the measurements (0.5%F.S. 1 digit), resolution, 2000Hz sampling rate, displays fully consistent with the airframe structureHTGS as standardCompareSpHTGA high function.%2%2%2%2%2Four are missing: 1 1st/ 2nd double peak test; 2 torque peak angle test; 3 specify zero angle for torque; 4 U disks are stored directly and entered (spaced) output._ If only hand-held screws, bolts, knobs, switches are stunned / or a curve is collected with USB, HTGS is fully functional; to do torque-angle analysis, is fully effective; to do tort-angle analysis, torangles, tort to do Do not receive a computer to store directly on the U Disk, then choose HTGA
Q: What about the four-point process?!
A: Best selected for routine test tox-falling at full capacity 20%80%. Precision screws, glasses screws, shell screws, laptop screwsHTGS-0.5N(0.5 N·m); mobile phone screws, mini-house screws, spin button switches, spin button hand-scan testHTGS-2N(2 N·m, most commonly); conventional bolts, large knobs, valve handlesHTGS-5N(5 N·m); industrial bolts, toggler set-value verification, when larger surplus is requiredHTGS-10N(10 N·m). A small torque is a lot of ways to lose the sense of difference. Don't be too big
Q: Is the test clip a label?
A:No, it's notThe official and specified host of IMADA does not contain test clips and is to be selected separately in sample form: TA-00 small lock-tightfold (with AA-00 clamp), (a) The holding of 0.5 — 6.5mm) is suitable for screws and axes; TA-01 for square heads at four corners; TA-02 for torque head interfaces; The size of the TA-03 folder is suitable for larger samples. The alien sample can be contacted to make non-codile devices.. It is recommended that the fixed SHT-5N sensor seat (10N·m not applicable) or the homemade clip be used
Q: What difference does it make to the Twisted Bottle Q?. Reference: HTGS, DTXS
A: DTXS YesDesktop_Funct_BAR__FuncInstrument, with a ping-and-doo table, special test for caps, container openings/ closed bolt torque, sample on the platform; HTGS YesHandhelddisplays are separated from the sensor (intermediately connected by a spiral spring line), the sensor has a front end clip that can be reached inside the device or at the production line level, and the screws, bolts, knobs, switches, rotor stubble and twisting. The accuracy of the two is the same as the sampling rate. The choice depends on the sample form and the test location.!
Q: How do you export data to computers?!??
A: Marked USB data lines, connected to the computer as a virtual COM port, attached to the Lo. data recording software, capture rate 10 data/sec, The maximum, minimum, average value is automatically counted for CSV stored; there is also a 1000 point stored on the machine that can be downloaded after the fact._ Requires real-time torque curves (up to 2000Hz) to be extra-suited to the ulazer software;_ Also you can export RS232C/ kimimatic/ analogue output to PLC or printer. Note: HTGS does not support U-disposal, Select HTGA for offline high capacity records.!
All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.
For a quotation, lead time or an optional calibration certificate, please contact our engineers.