IMADA MX3-500N Force & Material Testing (Model MX3-500N) is a Force & Material Testing supplied by Guangzhou Yunke Electronics Co., Ltd. IMADA MX3-500N Force & Material Testing — Force & Material Testing · Yunke Electronics. Request a quotation and datasheet.
Brand: IMADA | Category: Force & Material Testing
Sales Inquiries: 15626018696 · 78403603@qq.com

| Model | MX3-500N |
|---|---|
| Series | MX3 Series Type Standard Motorised Unit units (IMADA JapanIMADA, MX2 Replace Unit Type) |
| Type | Type / Standard Type Motorised Unit units (Standard Type, New a ) |
| Maximum Load | 500 N |
| Test Speed | 10 ~ 300 mm / min(0.5 mm / min Setting) |
| Maximum Sample Height | Approx. 235 mm(units Surface to Measure Rod Tip, Installed ZTS / ZTA ≤1000N General-purpose Type when) |
| Structure Degree | Standard Type 0.5 mm or less; Length Stroke -L 1.0 mm or less; -2L 2.0 mm or less |
| Stroke Limit | 2 pcs Stroke Limit Knob + Number digits Stroke Setting |
| Test Mode | Automatic Test Mode (Auto Test Mode) / Manual Test Mode |
| Counting and When | Counting: up to 99999 times; Setting when: most Length 99 Division 59.9 s (0.1 s ) |
| Control and Safety | per Knob, Force Value Control, Overload , Setting Functions (a Setting / Test Conditions ) |
| Power Supply | AC100 ~ 240V, 50 / 60Hz(optional 100 / 120 / 230V) |
| Power Consumption | 50 W |
| Net Weight | Approx. 17 kg |
| Supplied Accessories | Operating Manual, Power Cable, Use , Tool, GF-1 Fixture Installation Rotation Connection Device, USB Wire, Test Conditions Setting Software CS Test Preset Builder |
| Optional with | -L(Stroke +200mm), -2L(Stroke +400mm), -CN external Connection Signal Input Output, -FA Built-in Linear Scale, -V45 / -V90 / -V450 / -V600 / -V900 Speed Range more (-V600 Capacity to 250N, -V900 to 150N) |
| Matching Measuring Force Meter | DST / DSV, ZTS / ZTA Series ( optional) |
| Notes | This unit units is plus Unit , Force Value by with Force Gauges Reading Output, Force Gauges optional. Speed Setting Accuracy 0.5 mm / min, Positioning and Repeatability Optimum at above a MX2. |
Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.
Applies to samples of electronic components, connectors and beams, key and switch, springs, rubber and plastics, film and glue, packaging and paper, hardware, textiles and wires, etc., stretching, compressing, stripping, plugging, etc. The curves and damage tests impose a stable, consistent load. The electronics, connectors and beams, auto parts, hardware plastics, packaging printing, medical equipment and the materials testing, research and development of certification and the grade of the gymnastics.Stights and test materials
Q: The MX3-500N platform contains a non-pull puller?
A: Excludes. The platform is only loaded with the implementing agency and the force value is read out by the thrusting measure attached.. The station can be equipped with a separate IMADA (IMADA) ZTS/ZTA or DST/DSV high-value ratio booster. / DSV XVV XV XV elect the corresponding process according to the range of measured values
Q: What are the stages of the thruster that can be assigned to the platform?
A: DST/DSV, ZTS/ZTA series thrust meters, with the following sequences, which are officially appropriate. The actual measurement cap is based on the desktop capacity 500 N - when the measurement of force is greater than the desktop capacity, only the desktop capacity is measured..SQ capacity is the maximum capacity of the platform. Reference: 500 N
Q: What's the difference between MX3-500N and MX2-500N? Q: Q: Q
A: MX3 is a replacement type for MX2. The main difference is: MX3 speed set step 0.5 mm/min (MX2 in three steps); Quest QuestStamps Quest QuancessStightsssssStightsStrates MX3 randomly attached CSJJPPer test conditions setting software with USB line to support the organization of automated test conditions on computers; MX3 Counting cap 99999 (MX2 for 65535); MX3 adding general locks and test conditions
Q: What can autotest models do?
A: Autotest models can automatically move the meter within a given range of processes and perform stop, reverse, maintain actions at a given strength, and can also set the number of repeats and standstill times;_ The CSJJP is programmed on a computer with one key call to reduce manual error
Q: Does the change of speed range option affect capacity? Q
A: Will. The capacity of-V600 (20 — 600 mm/min) is reduced to 250 N, -V900 (30 — 900 mm/min) capacity reduced to 150 N; -V45/-V90/-V450 does not affect 500 N capacity. XQZX X X ZX hen selecting a model, you should be weighed against the actual speed and strength requirement.!
All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.
For a quotation, lead time or an optional calibration certificate, please contact our engineers.