IMADA EMX-500N Force & Material Testing (Model EMX-500N) is a Force & Material Testing supplied by Guangzhou Yunke Electronics Co., Ltd. IMADA EMX-500N Force & Material Testing — Force & Material Testing · Yunke Electronics. Request a quotation and datasheet.
Brand: IMADA | Category: Force & Material Testing
Sales Inquiries: 15626018696 · 78403603@qq.com

| Model | EMX-500N |
|---|---|
| Series | EMX Series Type Height Functions Motorised Unit units (IMADA JapanIMADA) |
| Type | Type / Height Functions Type Motorised Unit units (Advanced Type) |
| Maximum Load | 500 N |
| Test Speed | 0.5 ~ 600 mm/min(0.5 ~ 20:0.5 mm/min;20 ~ 100:5 mm/min;100 ~ 600:10 mm/min) |
| Maximum Sample Height | 280 mm |
| Structure Degree | Standard Type 0.25 mm or less; Length Stroke (-L)0.6 mm or less |
| Stroke Limit | above, Lower Limit digits Knob + Number digits Displacement Limit digits (0.1 mm ) |
| Test Mode | Manual Mode / JOG Micro Mode / Ring Mode |
| Counting and When | Counting: up to 65535 times; Setting when: most Length 99 Division 59.9 s (0.1 s ) |
| Conditions Memory | Storable 5 groups Test Conditions (incl. Conditions Control) |
| Detection Functions | CONTACT DETECTION(Contact Detection), BREAK DETECTION( Detection), two not can Same when Operating |
| Control and Safety | per Knob, Force Value Control, Overload , External Signal Input, Single Setting |
| Power Supply | AC100 ~ 240V, 50 / 60Hz(optional 100 / 120 / 230V) |
| Power Consumption | 50 W |
| Dimensions | Approx. Width 220 × Depth 380 × Height 637 mm |
| Net Weight | Approx. 19 kg |
| Optional with | -L(Stroke +300mm), -FA Built-in Linear Scale |
| Matching Measuring Force Meter | DST / DSV, ZTS / ZTA Series ( optional) |
| Notes | This unit units is plus Unit , Force Value by with Force Gauges Reading Output, Force Gauges optional. Displacement can Number digits Setting, Repeat Positioning Accuracy Height at Standard Type. |
Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.
Applies to samples of electronic components, connectors and beams, key and switch, springs, rubber and plastics, film and glue, packaging and paper, hardware, textiles and wires, etc., stretching, compressing, stripping, plugging, etc. The curves and damage tests impose a stable, consistent load. The electronics, connectors and beams, auto parts, hardware plastics, packaging printing, medical equipment and the materials testing, research and development of certification and the grade of the gymnastics.Stights and test materials
Q: The EMX series contains a non-pull puller?
A: Excludes. The platform is only loaded with the implementing agency and the force value is read out by the thrusting measure attached.. The station can be equipped with a separate IMADA (IMADA) ZTS/ZTA or DST/DSV high-value ratio booster. / DSV XVV XV XV elect the corresponding process according to the range of measured values
Q: What are the stages of the thruster that can be assigned to the platform?
A: DST/DSV, ZTS/ZTA series thrust meters, with the following sequences, which are officially appropriate. The actual measurement cap is based on the desktop capacity 500 N - when the measurement of force is greater than the desktop capacity, only the desktop capacity is measured..SQ capacity is the maximum capacity of the platform. Reference: 500 N
Q: What is the difference between exposure and fracture detection?
A: CONTACT DETECTION recorded the position as soon as the sample was first exposed to the head and the force value rose from zero; BREAK DETECTION recorded the position as soon as the sample was broken and the force dropped. he two are used to determine the starting and the destruction points respectively, but the official indication is that they cannot be used simultaneously.?
Q: EMX and MX2
A: MX2 is sufficient if only numbers are required to set speed, count and time; if digital displacement is also required, contact/ break detection, A wider 0.5 — 600 mm/min speed range and higher airframe readiness, with EMX selected
Q: What use is the built-in linear ruler for --FA?
A:-FA has linear scales on the platform for the output of the migration data for the meter; and the measurement meters (e.g. ZTA series) and special cable to support the displacement of the I/O, Qatar It's a power-diversion analysis.!
All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.
For a quotation, lead time or an optional calibration certificate, please contact our engineers.