IMADA EMX2-500N Force & Material Testing (Model EMX2-500N) is a Force & Material Testing supplied by Guangzhou Yunke Electronics Co., Ltd. IMADA EMX2-500N Force & Material Testing — Force & Material Testing · Yunke Electronics. Request a quotation and datasheet.
Brand: IMADA | Category: Force & Material Testing
Sales Inquiries: 15626018696 · 78403603@qq.com

| Model | EMX2-500N |
|---|---|
| Series | EMX2 Series Type Height Functions Motorised Unit units (IMADA JapanIMADA, EMX Replace Unit Type) |
| Type | Type / Height Functions Type Motorised Unit units (Advanced Type, New a ) |
| Maximum Load | 500 N |
| Test Speed | Number digits Setting 0.5 ~ 600 mm / min(0.1 mm / min ) |
| Maximum Sample Height | Standard Type Approx. 280 mm; Length Stroke -L Approx. 580 mm |
| Structure Degree | Standard Type 0.25 mm or less; Length Stroke (-L)0.6 mm or less |
| Stroke Limit | above, Lower Limit digits Knob + Number digits Displacement Limit digits (0.1 mm ) |
| Test Mode | Automatic Test Mode (Auto Test Mode) / Manual Test Mode |
| Counting and When | Counting: up to 99999 times; Setting when: most Length 99 Division 59.9 s (0.1 s ) |
| Conditions Memory | up to 10 groups Test Conditions (incl. Conditions Control) |
| Detection Functions | CONTACT DETECTION(Contact Detection), BREAK DETECTION( Detection), two not can Same when Operating |
| Control and Safety | per Knob, Force Value Control, Overload , Specified Stroke Shift , External Signal Input Output, Setting Functions |
| Operating Environment | Environment Temperature 0 ~ +40 ℃; Relative Humidity 85% or less (non-condensing) |
| Power Supply | AC100 ~ 240V, 50 / 60Hz(optional 100 / 120 / 230V) |
| Power Consumption | 50 W |
| Net Weight | Standard Type Approx. 19 kg; Length Stroke -L Approx. 24 kg |
| Supplied Accessories | Operating Manual, Power Cable, Use , Tool, Fixture Installation Rotation Connection Device (GF-1), Protection Accessories (only -L), USB Wire, Test Conditions Setting Software CS Test Preset Builder |
| Optional with | -L(Stroke +300mm), -FA Built-in Linear Scale |
| Matching Measuring Force Meter | DST / DSV, ZTS / ZTA Series ( optional) |
| Notes | This unit units is plus Unit , Force Value by with Force Gauges Reading Output, Force Gauges optional. |
Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.
Applies to samples of electronic components, connectors and beams, key and switch, springs, rubber and plastics, film and glue, packaging and paper, hardware, textiles and wires, etc., stretching, compressing, stripping, plugging, etc. The curves and damage tests impose a stable, consistent load. The electronics, connectors and beams, auto parts, hardware plastics, packaging printing, medical equipment and the materials testing, research and development of certification and the grade of the gymnastics.Stights and test materials
Q: The EMX2 series contains a non-pull puller?
A: Excludes. The platform is only loaded with the implementing agency and the force value is read out by the thrusting measure attached.. The station can be equipped with a separate IMADA (IMADA) ZTS/ZTA or DST/DSV high-value ratio booster. / DSV XVV XV XV elect the corresponding process according to the range of measured values
Q: What are the stages of the thruster that can be assigned to the platform?
A: DST/DSV, ZTS/ZTA series thrust meters, with the following sequences, which are officially appropriate. The actual measurement cap is based on the desktop capacity 500 N - when the measurement of force is greater than the desktop capacity, only the desktop capacity is measured..SQ capacity is the maximum capacity of the platform. Reference: 500 N
Q: What's the difference between EMX2 and EMX? Q: Q: Q
A: EMX2 is a replacement type for EMX: velocity setting from slotting to 0.1 mm/min continuous; Conditions storage from 5 to 10;. Adding automatic test mode with CSPer test conditions set software (randomly attached to USB line); counting cap 99999;;Stamping of the data from the dataset of the datasets;Standing of the data from the data files; of the data files of the data files; of the data files of the data files; of the data files of the data files; of the data on the data and add a general set lock, test number lock and test condition lock
Q: Can exposure and break detection be used simultaneously?
A: No. Officially it is clear that CONTACT DETECTION is not enabled simultaneously with BREAK DETECTION, and is selected for the purposes of the test
Q: How much height and weight would the long-distance process-L increase?
A: This type -L increases the length of the journey and the pillar 300 mm, with the maximum sample height from about 280 mm to about 580 mm; The weight increased from about 19 kg to about 24 kg, with random anti-dumping attachments
All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.
For a quotation, lead time or an optional calibration certificate, please contact our engineers.