Home › Products

Product Overview

IMADA EMX2-1000N Force & Material Testing (Model EMX2-1000N) is a Force & Material Testing supplied by Guangzhou Yunke Electronics Co., Ltd. IMADA EMX2-1000N Force & Material Testing — Force & Material Testing · Yunke Electronics. Request a quotation and datasheet.

Brand: IMADA | Category: Force & Material Testing

Sales Inquiries: 15626018696 · 78403603@qq.com

IMADA EMX2-1000N Force & Material Testing

Technical Specifications

ModelEMX2-1000N
SeriesEMX2 Series Type Height Functions Motorised Unit units (IMADA JapanIMADA, EMX Replace Unit Type)
TypeType / Height Functions Type Motorised Unit units (Advanced Type, New a )
Maximum Load1000 N
Test SpeedNumber digits Setting 0.5 ~ 600 mm / min(0.1 mm / min )
Maximum Sample HeightStandard Type Approx. 310 mm; Length Stroke -L Approx. 610 mm
Structure DegreeStandard Type 0.25 mm or less; Length Stroke (-L)0.6 mm or less
Stroke Limitabove, Lower Limit digits Knob + Number digits Displacement Limit digits (0.1 mm )
Test ModeAutomatic Test Mode (Auto Test Mode) / Manual Test Mode
Counting and WhenCounting: up to 99999 times; Setting when: most Length 99 Division 59.9 s (0.1 s )
Conditions Memoryup to 10 groups Test Conditions (incl. Conditions Control)
Detection FunctionsCONTACT DETECTION(Contact Detection), BREAK DETECTION( Detection), two not can Same when Operating
Control and Safetyper Knob, Force Value Control, Overload , Specified Stroke Shift , External Signal Input Output, Setting Functions
Operating EnvironmentEnvironment Temperature 0 ~ +40 ℃; Relative Humidity 85% or less (non-condensing)
Power SupplyAC100 ~ 240V, 50 / 60Hz(optional 100 / 120 / 230V)
Power Consumption50 W
Net WeightStandard Type Approx. 27 kg; Length Stroke -L Approx. 33 kg
Supplied AccessoriesOperating Manual, Power Cable, Use , Tool, Fixture Installation Rotation Connection Device (GF-2), Protection Accessories (only -L), USB Wire, Test Conditions Setting Software CS Test Preset Builder
Optional with-L(Stroke +300mm), -FA Built-in Linear Scale
Matching Measuring Force MeterDST / DSV, ZTS / ZTA Series ( optional)
NotesThis unit units is plus Unit , Force Value by with Force Gauges Reading Output, Force Gauges optional.

Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.

Product Description


Key Advantages

  1. EMX replacement type: enhances the operation on the basis of EMX high function, with speed setting steps to fine-tune to 0.1 mm/min, with conditions to store the 10 group. XC:Sec.SpSpSp.Sp.Sp.Sp.Sp
  2. Autotest mode + Specialized software: Randomly Attached CSJJPer Test Condition Setup Software with USB Line,Standed by USBStandardsStamped by CSJPStandardsStanded by the X by the X-StandardsStights You can organize process and strength conditions (stop/ reverse/ maintain) on a computer and run automatically, and operate more easily.Press & & &
  3. Digital shift limit + high strenchment: The move can be set at 0.1 mm step by step, with a body size of 0.25 mm below (long-range process 0.6 mm), duplicate positioning precision
  4. Exposure / break detection: Automated capture of the moment the head first touches the sample and the sample breaks, the key life, the plug-in force, and the destruction of the test need not be manually observed
  5. 10 group conditions storage and locking function: A common condition key is called; the locking function prevents the parameter from being mischanged and is suitable for multiple users
  6. Long-range -L: Process and pillar length 300 mm, standard maximum sample height approximately 310 mm up to about 610 mm, suitable for long sample and high extension material
  7. Full security: emergency, force level control, overload stop and external signal I/O ready to be locked between production lines

Applied trade & test object

Applies to samples of electronic components, connectors and beams, key and switch, springs, rubber and plastics, film and glue, packaging and paper, hardware, textiles and wires, etc., stretching, compressing, stripping, plugging, etc. The curves and damage tests impose a stable, consistent load. The electronics, connectors and beams, auto parts, hardware plastics, packaging printing, medical equipment and the materials testing, research and development of certification and the grade of the gymnastics.Stights and test materials

FAQ

Q: The EMX2 series contains a non-pull puller?

A: Excludes. The platform is only loaded with the implementing agency and the force value is read out by the thrusting measure attached.. The station can be equipped with a separate IMADA (IMADA) ZTS/ZTA or DST/DSV high-value ratio booster. / DSV XVV XV XV elect the corresponding process according to the range of measured values

Q: What are the stages of the thruster that can be assigned to the platform?

A: DST/DSV, ZTS/ZTA series thrust meters, with the following sequences, which are officially appropriate. The actual measurement cap is based on the desktop capacity 1000 N - when the measurement of force is greater than the desktop capacity, only the desktop capacity is measured..SQ capacity is the maximum capacity of the platform. Reference: 1000 N

Q: What's the difference between EMX2 and EMX? Q: Q: Q

A: EMX2 is a replacement type for EMX: velocity setting from slotting to 0.1 mm/min continuous; Conditions storage from 5 to 10;. Adding automatic test mode with CSPer test conditions set software (randomly attached to USB line); counting cap 99999;;Stamping of the data from the dataset of the datasets;Standing of the data from the data files; of the data files of the data files; of the data files of the data files; of the data files of the data files; of the data on the data and add a general set lock, test number lock and test condition lock

Q: Can exposure and break detection be used simultaneously?

A: No. Officially it is clear that CONTACT DETECTION is not enabled simultaneously with BREAK DETECTION, and is selected for the purposes of the test

Q: How much height and weight would the long-distance process-L increase?

A: This type -L increases the length of the journey and the pillar 300 mm, with the maximum sample height from about 310 mm to about 610 mm; The weight increased from about 27 kg to about 33 kg, with random anti-dumping attachments

All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.

For a quotation, lead time or an optional calibration certificate, please contact our engineers.

Related Products

IMADA ZU-20kN Force & Material Testing
Force & Material Testing

IMADA ZU-20kN Force & Material Testing

ZU-20kN
└ IMADA (Japan)
IMADA ZU-10kN Force & Material Testing
Force & Material Testing

IMADA ZU-10kN Force & Material Testing

ZU-10kN
└ IMADA (Japan)
IMADA XY-500N-EZ Force & Material Testing
Force & Material Testing

IMADA XY-500N-EZ Force & Material Testing

XY-500N-EZ
└ IMADA (Japan)
IMADA XY-500N-M8 Force & Material Testing
Force & Material Testing

IMADA XY-500N-M8 Force & Material Testing

XY-500N-M8
└ IMADA (Japan)
IMADA XY-500N-BB Force & Material Testing
Force & Material Testing

IMADA XY-500N-BB Force & Material Testing

XY-500N-BB
└ IMADA (Japan)
IMADA XY-500N Force & Material Testing
Force & Material Testing

IMADA XY-500N Force & Material Testing

XY-500N
└ IMADA (Japan)