Home › Products

Product Overview

IMADA MH-1000N Force & Material Testing (Model MH-1000N) is a Force & Material Testing supplied by Guangzhou Yunke Electronics Co., Ltd. IMADA MH-1000N Force & Material Testing — Force & Material Testing · Yunke Electronics. Request a quotation and datasheet.

Brand: IMADA | Category: Force & Material Testing

Sales Inquiries: 15626018696 · 78403603@qq.com

IMADA MH-1000N Force & Material Testing

Technical Specifications

ModelMH-1000N
SeriesMH Series Type Motorised Unit units (IMADA JapanIMADA)
TypeType / Type Motorised Unit units (Horizontal, Simple Type)
Maximum Load1000 N
Test Speed6 ~ 180 mm/min
Maximum Sample LengthApprox. 280 mm
Stroke Limitabove, Lower Limit digits Knob Manual Adjustment
Test ModeManual Mode / Single times Ring Mode / Continuous Ring Mode
Control and Safetyper Knob, Overload , Force Value Control (requires with compatible Measuring Force Meter and Dedicated Cable)
Power SupplyAC100 ~ 240V, 50 / 60Hz(optional 100 / 120 / 230V)
Power Consumption50 W
DimensionsApprox. Width 700 × Depth 195 × Height 210 mm
Net WeightApprox. 14 kg
Optional with-E Speed and Length Meter, -S Length Scale
Matching Measuring Force MeterDST / DSV, ZTS / ZTA Series ( optional)
NotesThis unit units is plus Unit , Force Value by with Force Gauges Reading Output, Force Gauges optional. Type Structure, Sample , Installed Clamp more Method .

Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.

Product Description


Key Advantages

  1. Bed structure: Samples are horizontally placed, clips are easier to form in contrast to the center, and are particularly suitable for long stripes, slenders and cable types.!
  2. Electro-input: Power drive replaces manual power, with uniform speed and consistent direction, with a better repeat than manual
  3. Three test models: manual, single loop and continuous loop, which can be repeated between slot limits and suitable for the re-test of insertion and stripping
  4. Power control and overload protection: in conjunction with compatible measurement and special cable, the power gauge can be stopped at the preset value and the stop buttons protect the meter
  5. Manually sets the process: the top-down buttons directly lock the process range and the product changes quickly.!
  6. Broad voltage design: AC100 — 240V self-adapted, optional version 100 / 120 / 230V. X-X-X-X-X-. X-ZX-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X

Applied trade & test object

Applies to samples of electronic components, connectors and beams, key and switch, springs, rubber and plastics, film and glue, packaging and paper, hardware, textiles and wires, etc., stretching, compressing, stripping, plugging, etc. The curves and damage tests impose a stable, consistent load. The electronics, connectors and beams, auto parts, hardware plastics, packaging printing, medical equipment and the materials testing, research and development of certification and the grade of the gymnastics.Stights and test materials

FAQ

Q: The MH series contains a non-pull puller?

A: Excludes. The platform is only loaded with the implementing agency and the force value is read out by the thrusting measure attached.. The station can be equipped with a separate IMADA (IMADA) ZTS/ZTA or DST/DSV high-value ratio booster. / DSV XVV XV XV elect the corresponding process according to the range of measured values

Q: What are the stages of the thruster that can be assigned to the platform?

A: DST/DSV, ZTS/ZTA series thrust meters, with the following sequences, which are officially appropriate. The actual measurement cap is based on the desktop capacity 1000 N - when the measurement of force is greater than the desktop capacity, only the desktop capacity is measured..SQ capacity is the maximum capacity of the platform. Reference: 1000 N

Q: What are the samples suitable for the bedside?

A: A sample of the type of strip, snippet, cable and connector. Samples are placed horizontally, with a better fit of clamp and pairing, and are often used for the plug-in, stripping and horizontal pull tests

Q: Can speed be set numerically? Q

A: MH-1000N is simple and the speed is adjusted by the panel knob (6 ~ 180 mm/min) process is fixed by the top and bottom bit buttons, without numerical setting; If numbers are required to set speed, counting and timing, select the MH2 series

Q: And what about the MH2 series?

A: MH-1000N is a front-page type suitable for a batch test with fixed test conditions; the MH2 series is standard type with a speed set, measured and fixed, and with a length ruler, The built-in linear ruler interface with the external signal interface is appropriate for the test for which the conditions for recovery are required

All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.

For a quotation, lead time or an optional calibration certificate, please contact our engineers.

Related Products

IMADA ZU-20kN Force & Material Testing
Force & Material Testing

IMADA ZU-20kN Force & Material Testing

ZU-20kN
└ IMADA (Japan)
IMADA ZU-10kN Force & Material Testing
Force & Material Testing

IMADA ZU-10kN Force & Material Testing

ZU-10kN
└ IMADA (Japan)
IMADA XY-500N-EZ Force & Material Testing
Force & Material Testing

IMADA XY-500N-EZ Force & Material Testing

XY-500N-EZ
└ IMADA (Japan)
IMADA XY-500N-M8 Force & Material Testing
Force & Material Testing

IMADA XY-500N-M8 Force & Material Testing

XY-500N-M8
└ IMADA (Japan)
IMADA XY-500N-BB Force & Material Testing
Force & Material Testing

IMADA XY-500N-BB Force & Material Testing

XY-500N-BB
└ IMADA (Japan)
IMADA XY-500N Force & Material Testing
Force & Material Testing

IMADA XY-500N Force & Material Testing

XY-500N
└ IMADA (Japan)