Home › Products

Product Overview

IMADA SVL-1000N Force & Material Testing (Model SVL-1000N) is a Force & Material Testing supplied by Guangzhou Yunke Electronics Co., Ltd. IMADA SVL-1000N Force & Material Testing — Force & Material Testing · Yunke Electronics. Request a quotation and datasheet.

Brand: IMADA | Category: Force & Material Testing

Sales Inquiries: 15626018696 · 78403603@qq.com

IMADA SVL-1000N Force & Material Testing

Technical Specifications

ModelSVL-1000N
SeriesSVL Series Type Manual Test Unit units (IMADA JapanIMADA)
TypeType / Wrench Rod Type Manual Test Unit units (Lever Type)
Maximum Load1000 N
Maximum Sample HeightApprox. 225 mm(units Surface to Measure Rod Tip, Installed ZTS / ZTA ≤1000N General-purpose Type when)
Maximum Stroke60 mm(Wrench Rod Rotation 170°)
Quantity60 mm / Wrench Rod 170°
Operation MethodPressure under Wrench Rod plus
DimensionsApprox. Width 200 × Depth 280 × Height 410 mm
Net WeightApprox. 7.3 kg
Optional with-S Length Scale, -EXT Extended Column (Stroke Unchanged)
Matching Measuring Force MeterDST / DSV, ZTS / ZTA Series ( optional)
NotesThis unit units is plus Unit , Force Value by with Force Gauges Reading Output, Force Gauges optional. Wrench Rod Type Operation, Single i.e. can plus .

Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.

Product Description


Key Advantages

  1. (b) Curb operation: A single load can be quickly completed by pressing the trigger, which is one-hand operation, efficient and suitable for batch double testing
  2. (b) A simple-structured free of power: a purely mechanical structure that does not require electricity, is suitable for a non-electrical position or for an electromagnetic environment-sensitive situation.?
  3. Manual load-loading is good: the station fixes the direction and angle of the force, and the repeat is much higher than the hand-held measurement
  4. Small and light: about 7.3 kg, the smallest paragraph in the SV series, which facilitates movement and multi-point placement
  5. Process 60 mm: meets the pressure and stripping test requirements of most small samples
  6. Addable length ruler: The distance of the measurement machine can be read directly after the selection -S.SS
  7. Official position: The SV series is a simple (Sioulà) version of the manual test platform, which officially points to Leverou as a measurer, as a tool for measuring efficiency, Handhold (Handleou) stabilization measurements - SVL-1000N is the former, and load can be done by pressing the trigger.?
  8. A station-fixed test angle: Manual stations provide a constant force angle, with greater repetition than hand-held measurements (officially stated), and thus more consistent testing conditions for the same samples.?.Stamps are more common.Stight
  9. Addable -EXT with long columns: The longer-long loading space is larger, but the measuring process remains unchanged (official statement)
  10. The combination is clear: the matrix is built in the official "board plus meter plus clip" and is fixed on the platform's installation seat, and the trap is installed between the meter and the table, and a platform can be fitted with different sets of clips and multiple samples

Applied trade & test object

Applies to samples of electronic components, connectors and beams, key and switch, springs, rubber and plastics, film and glue, packaging and paper, hardware, textiles and wires, etc., stretching, compressing, stripping, plugging, etc. The curves and damage tests impose a stable, consistent load. The electronics, connectors and beams, auto parts, hardware plastics, packaging printing, medical equipment and the materials testing, research and development of certification and the grade of the gymnastics.Stights and test materials

(a) The method of loading the meter into the platform assembly, the corresponding kit between the meter and the platform, which is loaded by pressure on the trigger after the sample is placed; the platform provides a constant elastic angle of application;_ The test conditions for the same samples were therefore more consistent and more repetitive than hand-held measurements

The loading of the clamp-tocking equipment on the platform also requires an official additional GF-1/GF-2 relay (officially marked as a transfer necessary to install the clamp-tock on the platform, to be sold); -EXT plus long columns and -S length scale are also official optionals

Sample height description: The maximum sample height (or maximum sample length) in the specification indicates the distance between the table floor and the screw of the forceometer (the gauge is at the highest point, ZT Generalized 1000N and below; 3000N is calculated as a large-capacity type in the ZT series, without a thick content, The actual availability of heights varies slightly depending on the packaging.!

FAQ

Q: The SVL-1000N platform contains a non-pull puller?

A: Excludes. The platform is only loaded with the implementing agency and the force value is read out by the thrusting measure attached.. The station can be equipped with a separate IMADA (IMADA) ZTS/ZTA or DST/DSV high-value ratio booster. / DSV XVV XV XV elect the corresponding process according to the range of measured values

Q: What are the stages of the thruster that can be assigned to the platform?

A: DST/DSV, ZTS/ZTA series thrust meters, with the following sequences, which are officially appropriate. The actual measurement cap is based on the desktop capacity 1000 N - when the measurement of force is greater than the desktop capacity, only the desktop capacity is measured..SQ capacity is the maximum capacity of the platform. Reference: 1000 N

Q: What's the difference between SVL and SVH? Q: Q: Q

A: The two dimensions of capacity, sample height, and process are identical to the shape, and the difference is to be found in the operation: SVL-1000N is a wrench (loading the wrench under pressure) and SVH-1000N is a hand handle (loading the wheel handle). Quest. The wrench is faster and the handle is more smooth

Q: How many trips do you have to go for the wrench?. Reference: 170

A: The trigger is pressurized from top to bottom and rotates about 170°, the response measurement process is about 60 mm, covering the test distance of most small samples

Q: Do you need a power supply?

A: No. The platform is a purely manual mechanical structure, not requiring electricity, and is available with a push-and-pull array, suitable for unelectrical spaces or for situations sensitive to the electromagnetic environment

Q: Are the clips and relays randomly attached?

A: No collateral. The machine is only equipped with the machine's own body and the modeling and the meter, the clip and the switch are to be selected separately. The clips are selected by the sample shape and size - stretching the clip, compressing the presses, removing the wheeling and so on; Specific models can be confirmed by call.!

Q: How do you choose a hand and an electric platform?!

A: A simple, power-free, low cost, fixed-loaded angle and fixed-in-take load for a manual platform suitable for routine tests and tests with small sample size and low force value; if a numerical speed and process is required, loop load, Bulk automatic testing or force control, please select the MX/MX2/MX3/EMX series power-motivator station

Q: Does the wrench operate to cause a loss of reading of force?

A: No. The trigger, in conjunction with the screwdriver, moves at a constant speed, and the platform itself provides a constant angle of pressure, as long as the pace of the trigger is similar at each time._ The consistency of readings is significantly better than the direct pressure of handheld meter samples

All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.

For a quotation, lead time or an optional calibration certificate, please contact our engineers.

Related Products

IMADA ZU-20kN Force & Material Testing
Force & Material Testing

IMADA ZU-20kN Force & Material Testing

ZU-20kN
└ IMADA (Japan)
IMADA ZU-10kN Force & Material Testing
Force & Material Testing

IMADA ZU-10kN Force & Material Testing

ZU-10kN
└ IMADA (Japan)
IMADA XY-500N-EZ Force & Material Testing
Force & Material Testing

IMADA XY-500N-EZ Force & Material Testing

XY-500N-EZ
└ IMADA (Japan)
IMADA XY-500N-M8 Force & Material Testing
Force & Material Testing

IMADA XY-500N-M8 Force & Material Testing

XY-500N-M8
└ IMADA (Japan)
IMADA XY-500N-BB Force & Material Testing
Force & Material Testing

IMADA XY-500N-BB Force & Material Testing

XY-500N-BB
└ IMADA (Japan)
IMADA XY-500N Force & Material Testing
Force & Material Testing

IMADA XY-500N Force & Material Testing

XY-500N
└ IMADA (Japan)