Home › Products

Product Overview

ASKER C1L Hardness Testers (Model C1L) is a Hardness Testers supplied by Guangzhou Yunke Electronics Co., Ltd. ASKER C1L Hardness Testers — Hardness Testers · Yunke Electronics. Request a quotation and datasheet.

Brand: ASKER | Category: Hardness Testers

Sales Inquiries: 15626018696 · 78403603@qq.com

ASKER C1L Hardness Testers

Technical Specifications

ModelC1L
TypePointer Type Rubber Hardness Testers(アナログデュロメータ)
Applicable StandardJIS K 7312、JIS S 6050
Measurement Range0 ~ 100 points (262° Dial)
Minimum Scale1 points (Verification Accuracy ±1 points)
Indenter ShapeHeight 2.54mm, φ5.08mm Half
Spring Load0 points = 539mN(55g)/100 points = 8379mN(855g)
Plus Pressure Surfaceφ16mm(), Length Part L.18mm
DimensionsApprox. Width 57 × Depth 30 × Height 94mm
Weight200g
Primary ApplicationsRubber, , , Rubber , Wire,
Usageper Pressure Type, No requires Battery
OriginJapan Control (MADE IN JAPAN)
Model DescriptionC Type Length Type

Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.

Product Description


ModelYes, the rulesPump shape%Spring weightSpunner%1SMain purposeCreation of
AJIS K 6253-3、JIS K 7215、ASTM D 2240、ISO 48-4、ISO 868、DIN 53505Specifications: 2.50mm 0.79mm 35. Please contact our engineers for the full technical wording.0 point = 550mN (56g) / 100 point = 8050mN (821g)General rubberCrew%
ALJIS K 6253-3、JIS K 7215、ASTM D 2240、ISO 48-4、ISO 868、DIN 53505Specifications: 2.50mm 0.79mm 35. Please contact our engineers for the full technical wording.0 point = 550mN (56g) / 100 point = 8050mN (821g)General rubberCrew%
BASTM D 2240High 2.50mm, 30° conical, front-end R0.1mmSpwxSpS0 point = 550mN (56g) / 100 point = 8050mN (821g)Semi-hard rubber, sour-burned clay
BLASTM D 2240High 2.50mm, 30° conical, front-end R0.1mmSpwxSpS0 point = 550mN (56g) / 100 point = 8050mN (821g)Semi-hard rubber, sour-burned clay
CJIS K 7312、JIS S 6050High 2.54mm, 5.08mm Hemispheric0 point = 539mN (55g) / 100 point = 8379mN (855g)Soft rubber, polyurethane foam, sponges, rubber piping, curling, clay
C1LJIS K 7312、JIS S 6050High 2.54mm, 5.08mm Hemispheric0 point = 539mN (55g) / 100 point = 8379mN (855g)Soft rubber, polyurethane foam, sponges, rubber piping, curling, clay
C2—High 2.54mm, 5.08mm Hemispheric0 point = 539mN (55g) / 100 point = 4460mN (455g)Soft rubber, polyurethane foam, sponges, curls, film sheets, clay
C2L—High 2.54mm, 5.08mm Hemispheric0 point = 539mN (55g) / 100 point = 4460mN (455g)Soft rubber, polyurethane foam, sponges, curls, film sheets, clay
CS—High 2.54mm, 10mm cylinderScreak0 point = 980mN (100g) / 100 point = 44100mN (4500g)EPS (buffer plastic)
CSC2—High 2.54mm, 10mm cylinderScreak0 point = 539mN (55g) / 100 point = 4460mN (455g)EPS (buffer plastic)
DJIS K 6253-3、JIS K 7215、ASTM D 2240、ISO 48-4、ISO 868、DIN 53505High 2.50mm, 30° conical, front-end R0.1mmSpwxSpS0 point = 0mN (0g) / 100 point = 44500mN (4538g)Hard rubber, plastics
DLJIS K 6253-3、JIS K 7215、ASTM D 2240、ISO 48-4、ISO 868、DIN 53505High 2.50mm, 30° conical, front-end R0.1mmSpwxSpS0 point = 0mN (0g) / 100 point = 44500mN (4538g)Hard rubber, plastics
EJIS K 6253-3、ISO 48-4High 2.50mm, 5.00mm Hemispheric0 point = 550mN (56g) / 100 point = 8050mN (821g)Soft rubber, polyurethane foam, rubber sheeting
ELJIS K 6253-3、ISO 48-4High 2.50mm, 5.00mm Hemispheric0 point = 550mN (56g) / 100 point = 8050mN (821g)Soft rubber, polyurethane foam, rubber sheeting
F—High 2.54mm, 25.2mm cylinderScreak0 point = 539mN (55g) / 100 point = 4460mN (455g)Polyurethane foam, sponges, non-rotation
FP—High 2.54mm, 15mm cylinderScreak0 point = 980mN (100g) / 100 point = 1960mN (200g)Make-up powder.!
ISO-AJIS K 6253-3、JIS K 7215、ASTM D 2240、ISO 48-4、ISO 868、DIN 53505Specifications: 2.50mm 0.79mm 35. Please contact our engineers for the full technical wording.0 point = 550mN (56g) / 100 point = 8050mN (821g)General rubberCrew%
ISO-DJIS K 6253-3、JIS K 7215、ASTM D 2240、ISO 48-4、ISO 868、DIN 53505High 2.50mm, 30° conical, front-end R0.1mmSpwxSpS0 point = 0mN (0g) / 100 point = 44500mN (4538g)Hard rubber, plastics
JAJIS K 6301Specifications: 2.54mm 0.79mm 35. Please contact our engineers for the full technical wording.0 point = 539mN (55g) / 100 point = 8379mN (855g)General rubberCrew%
JALJIS K 6301Specifications: 2.54mm 0.79mm 35. Please contact our engineers for the full technical wording.0 point = 539mN (55g) / 100 point = 8379mN (855g)General rubberCrew%
JCJIS K 6301Specifications: 2.54mm 0.79mm 35. Please contact our engineers for the full technical wording.0 point = 980mN (100g) / 100 point = 44100mN (4500g)Hard rubber, plastics

Key Advantages

  1. Japanese original, ASKER official standard machine typeASKER (HCM) is a representative producer of rubber/plastic hardmeters in Japan, which are widely used in Japan and the domestic rubber industry. : Type A is the standard A hardmeter prescribed for JIS K 6253-3
  2. You don't need a battery, you take itMechanical pointer structure, free of electricity, charge and cable, ready for use in workshops, warehouses, spot checks and low maintenance costs for long-term use.!
  3. 262° Broadband Scale Disk, Read IntuitiveLarge t 'and long point-telemetry allows the naked eye to distinguish between 1 points, without additional displays or conversions; check for accuracy 1 points
  4. Selected by Hardware Material%from extremely soft polyurethane foams (E/F/FP) to general rubber (A/JA), soft rubber (C/C2), semi-hard (B), Hard rubber and plastic (type D) all types of samples covered by 21
  5. Long feet (L-type) detectable narrow / dent.%1%2AL / BL / C1L / C2L / DL / EL / JAL long footing to make the pressure face into foot / BL / C2L / DL / EL / JAL Q long foot to foot The way it was going.! Measurements that are not compatible with the general pressure surfaces of the dents, tubes, or alien matter, etc..SS
  6. The pressure-sized size is strictly equivalent.Charlierectangular 44 x 18mm (comparable JIS K 6253-3), Circle 18mm (ISO-A/ ISO-D for ISO 48-4), ZX 50mm (EXSZQ10 / CSC2), 80mm (Foot Material F) to ensure that measurement conditions are consistent with standards. Reference: CS
  7. A pressure-bound weighter, more standardized measureA combination of CL-150L pressure-fixing weights or CLE-150 electric charge-loaders, with a fixed constant charge weight applied by code or machine, to eliminate errors that do not match the pressure level of the handheld, (c) The requirement of weight for the standard is met
  8. Small size, easy to carryGeneral type approximately 200g, wide 57 x Deep 30 x High 76mm, which can be operated on a single hand or with the original factory box, suitable for travel and field use. : X x — High Z X X — High, X — high, X — high, — high, — high

Applied industry & test project

  • Industry: Rubber products, polyurethane foam and sponges, footwear, tyres and glues, plastics and engineering plastics, wire cables, film and packaging materials, cosmetics (poofing), scientific institutions and third-party testing agencies
  • Tests: Rubber hardness (silent at the silhouette level/international rubber hardness), flexible foam hardness, plastic hardness, glue hardness, sponge and non-swirling sheet hardness, XPS hardness, feed and out-of-work pumping

FAQ

Q: What is the relationship between ASKER and the common Shore hardometer?

A: The same instrument is essentially the "international rubber hardness" of rubber, which is expressed in the depth of the test by presses. ASKER (disappearance) is the Japanese brand, which corresponds to type Arad A for JIS K 6253-3Pump Specification, rad A withningre A for ASTM D 2240、rad A of ISO 48-4/ ISO 868The geometry of the pins corresponds to the spring weight, so the ASKERA and the NERA hardometers correspond directly to the standard level. Type A on this page is marked with JIS K 6253-3,. JIS K 7215, ASTM D 2240, ISO 48-4, ISO 868, DIN 53505 six specifications

Q: How do you choose a model by material??

A: The official principle of choice is - hardness is20 ~ 90 pointSplit%The most differentiated instructions are given. So: normal rubberType A(most common); if hard samples above 90 are detected using type A, they should be replacedCharliesChangeType D_Backgrounds_Backgroundsextreme soft samples below 20 should be replaced.%1%2%2%2%2%2%2%2Cl6T3T3T3E3Type C or Type EC or Epolyurethane foam, sponges, non-rotation, etc., for very soft materialsType F(Pressed surface 80mm); for EPSCS / CSC2Splitpowdered pistons and so forthSpecifications: FP. Please contact our engineers for the full technical wording.When the sample is narrow or indented, select the corresponding foot length (type L)

Q: Does the hard meter need regular calibration?

A: Need. Rubber hardness measures are measuring devices, where the wear and tear of the pressured needle shape and the change in the spring weight have a direct impact on the value, and it is recommended that the standard hard mass be used to validate the error in the value, which is regularly sent (usually once a year) to the enterprise measurement management system..Stamps are measuring instruments, and the standard hard mass is used to verify the error in the value. are the standard standards of the standard weight. This page does not include an official calibration cycle, based on the official instructions and local measurement protocols.!

Q: Is the measurements of handheld measurements and pressure-fixing weights much different?

A: There are differences. Handhelds are not always consistent in their pressure, angles, and stay periods, and are relatively less repetitive; the criteria provide for the application of weight and reading times for the tests, so that the regular tests should use the pressure-fixed weights. The daily screening is handheld-only, requiring regulation to be accompanied by a retrospective recommendation of CL-150L or CLE-150.ScopeScreen_Standards_Treatment_Text.Scope_Treatment_Textability

Q: Can you get data to output or access computers?

A: The pointer does not have an output interface itself, only manual reading; if data output and curve analysis are required, the selection is recommendedDigital DD5 / DD4 series(DD5 supports USB or RS-232C option one, DD4 is RS-232C) orAutomatic P2 series.Screaks-Screen(Ethernet interface, step-in motor controls down speed)._BAR_BAR

Q: Why are some models not marked, regulations?!?

A: This page strictly reproduces official labels. Specialized aircraft such as C2/ CS/ CSC2/ F/ FP, etc.ScreenScree / CS / CSC2 / F / FP The official product pages are not listed as valid, and the rules (which are the exclusive type of the manufacturer rather than the standard type) are therefore marked as "officially unlisted (specialized type of machine)" and are not speculative; for practical use, please refer to the official description and the test conditions

Q: Why is the same picture of the product?

A: ASKER Officially uses a uniform series of visual images of some types of aircraft (e.g. digital DD5-A sharing the same chart with DD5-D, which differs from the presses and presses). this site takes official pictures, and we have a video of the same image. Do not replace the penthouse. If you want to confirm the specific difference between the pressure needle and the pressure surface, please refer to the specification or call for advice.?.Stamp

Official Positioning Note: This model C1L is ASKER (Standard of High Molecular Calculators) soft rubber, polyurethane foam, sponges, rubber plating, curling, ceramic hardness meters, and the use of the X (Stamp of High Molecular Calculators) to control the use of the plastics and the use of the plastics. Pressured pin shape 2.54mm, ZQ4 Hemispheric,SpwxSp%SpwwSp Spring weight 0 point = 539mN (55g) / 100 point = 8379mN (855g) = 855g = ZXC = = Z = Z = = Z X = Z = = Z X X = = Z X = = he pressure surface 16mm (round) with a foot length L.18mm, which is mainly applied to soft rubber, polyurethane foam, sponges, rubber twigs, clay. ASKER is hardweighted to be made in Japan.ScreaksScortsssScres.sssss.ssssss The international rubber densities using the 0 — 100 points are used, and are broken down by material hardness, When selecting a model, please use the principle "squeaking in 20 ~ 90 point range".!. Reference: 5.08mm

Option hint: if a handheld is used for routine testing, care is taken to keep the pressure consistent with the angle; if used for regular testing or for measurement retroactive, The CL-150L pressure charger or CLE-150 electric charger are recommended. Guangzhou Yunke Electronics is available and the caller is welcome for the caller's selection and the charger

All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.

For a quotation, lead time or an optional calibration certificate, please contact our engineers.

Related Products

ASKER CL-150RC2 Hardness Testers
Hardness Testers

ASKER CL-150RC2 Hardness Testers

CL-150RC2
└ ASKER (Japan)
ASKER CL-150R2 Hardness Testers
Hardness Testers

ASKER CL-150R2 Hardness Testers

CL-150R2
└ ASKER (Japan)
ASKER CL-150RC1 Hardness Testers
Hardness Testers

ASKER CL-150RC1 Hardness Testers

CL-150RC1
└ ASKER (Japan)
ASKER CL-150R1 Hardness Testers
Hardness Testers

ASKER CL-150R1 Hardness Testers

CL-150R1
└ ASKER (Japan)
ASKER CL-150SL Hardness Testers
Hardness Testers

ASKER CL-150SL Hardness Testers

CL-150SL
└ ASKER (Japan)
ASKER CL-150H Hardness Testers
Hardness Testers

ASKER CL-150H Hardness Testers

CL-150H
└ ASKER (Japan)