BETTEN BTM-2000 Tension Meters (Model BTM-2000) is a Tension Meters supplied by Guangzhou Yunke Electronics Co., Ltd. BETTEN BTM-2000 Tension Meters — Tension Meters · Yunke Electronics. Request a quotation and datasheet.
Brand: BETTEN | Category: Tension Meters
Sales Inquiries: 15626018696 · 78403603@qq.com

| Model | BTM-2000 |
|---|---|
| Series | BETTEN BTM Series Width Width Material Tension Meter |
| Series Positioning | in Range Main Force Model |
| Tension Range | 20-2000 cN |
| Tension Range (Conversion) | Approx. 0.20~2.04 kgf |
| Typical Measured Material | Normal Gauge , , |
| Model Gauge Port | 20-2000 cN/CM |
| Accuracy | ±2% Full Scale (FS) |
| Display Update Rate | 0.5 s |
| Optional Unit | gf / cN / N / kgf / daN / LB(not Same Range switchable Unit not Same) |
| Display | points Type Display (Backlight LCD, Provided two Type not Same Display Interface) |
| Adjustable Range | Displayed Value can by per by Measured values 1% Width degrees ±10 Adjustment |
| Wire Speed | 1000 m/min |
| Storable Values | Minimum, Minimum Peak, Average |
| Data output | optional Wireless WIFI Output, with Wire Connection Number digits Output |
| Housing Dimensions | 393 × 146 × 78 mm |
| Power Supply | Rechargeable Battery, Continuous operation Approx. 10 hours |
| Operating Temperature | 0~45℃, 90% Relative Humidity or more |
| Standard Configuration List | Tension Instrument, Portable Type Instrument Gauge Case, Charger, in Text Manual, Pass / Fail |
| Application Range | No , , etc. each Type Width Width Material Tension Measurement |
Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.
| Model | Pressure Range | Conversion | Set Position | Typically measured material |
|---|---|---|---|---|
| BTM-500 | 5.0-500.0 cN | About 5.1 — 510 gf | A small amount of the BTM series | Twilight, thin, thin curtains, thin net |
| BTM-1000 | 10-1000 cN | About 10.2 — 1020 gf (approximately 1.02 kgf) | Small-scale GenericCl0C | General unwieldy, curtains, thin carbon fibre sheeting |
| BTM-2000 | 20-2000 cN | About 0.20 — 2.04 kgf | Medium-range main force modelCharlie | Regular curtain sheet, carbon fibre sheet, industrial netted |
| BTM-5000 | 50-5000 cN | About 0.51 — 5.10 kgf | It's a lot of time | Heavy curtain sheet, carbon fibre sheet, paper dry net |
| BTM-10K | 0.1-10.0 daN | 1 — 100 N (approximately 0.10 — 10.2 kgf) | DNN Quantum Transition Model | Heavy curtain sheet, wide-band carbon fibre sheet, paper blanket |
| BTM-20K | 0.2-20.0 daN | 2 — 200 N (approximately 0.20 — 20.4 kgf) | The most extensive of the BTM series | Super-wide heavy curtain sheeting, industrial blankets, heavy carbon fibre fabrics |
Q: Why do the cN, the cN/CM of the BTM series have a process of cN?
A: The official network BTM table labels the scale of the broad banding material as cN/CM (monized by width per centimetre) This scale 20-2000 cN takes the SKU icons (without / CM). Both are written by the same instrument according to different calibres, The selection is based on the actual material width and on-site process requirements, details of which may be consulted by telephone
Q: What is the difference between the BTM series and the NTW series?Seves
A: Both are directed towards broad-banded materials, but are located differently. The NTW series applies to narrow banding materials such as metallic thumps, tape, and so on, with a width less than 50mm. The head width of the measurements is 65 / 116 / 216mm in three stages; the BTM series is for non-width, curtain, carbon fibre ** material large.Asssembles Symblers Symmetrical Standards Standards Stands Stamps Standards St The shell size 393 x 146 x 78mm with a greater horizontal span
Q: How do you choose the BTM series?!?
A: Based on the actual tension of the measured material, it is recommended that the actual tension should fall to the full range of 20%~80%
Q: Can measurements be recorded??
A: Yes. The instrument records the maximum, minimum, peak, average values of the measurement process, and also memory the separate 199 measurements; Data output is selected for wireless WIFI output or cable connection digital output, which allows for quality recording and traceability
Q: What if the field material is not consistent with the plant marking?
A: The instrument can be marked with a maximum of 10 material; if it is only a minor deviation, the result fine-tuning function can be shown, adjusted 10 step by the range of the measured value 1%,Stamps of material, and then the 10 step by step, of the instrument, of the instrument, of the instrument, of the instrument, of the material, of the material, of the instrument, of the The exact value is not remarked.!
Q: Can the BTM series detect circular line material?
A: Not suitable. BTM series is designed for broad banding materials such as no spinning, curtains, carbon fibre sheets, and round wires are selected for NT series or other line item tension instruments. Q1 series or other liner tension instruments
All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.
For a quotation, lead time or an optional calibration certificate, please contact our engineers.