TECLOCK GS-607 Hardness Testers (Model GS-607) is a Hardness Testers supplied by Guangzhou Yunke Electronics Co., Ltd. TECLOCK GS-607 Hardness Testers — Hardness Testers · Yunke Electronics. Request a quotation and datasheet.
Brand: TECLOCK | Category: Hardness Testers
Sales Inquiries: 15626018696 · 78403603@qq.com

| Model | GS-607 Series (GS-607 / GS-607A / GS-607B / GS-607C) |
|---|---|
| Type | Hardness Testers Test Device (Hardness Testers Load Check Device) |
| Check Management | Hardness Testers Installed Clamp, Use 3 pcs Reference Weight plus Gauge Setting Load, Check Dial 25, 50, 75 three points Yes No Correction Accuracy Indication |
| Check Point Digit | Dial 25 / 50 / 75(to Dial above ● ) |
| Indication Value Error | ±1 points |
| Applicable Unit Type GS-607 | GS-701N / GS-701G / GS-706N / GS-706G |
| Applicable Unit Type GS-607A | GS-709N / GS-709G |
| Applicable Unit Type GS-607B | GS-719N / GS-719G / GS-721N / GS-721G / GS-750G / GS-753G |
| Applicable Unit Type GS-607C | GS-743G |
| Mass | 3.7kg(Full Series total General) |
| Calibration Part | can Calibration (Number digits Type Hardness Testers and Product Calibration not can) |
| Origin | Japan Control (MADE IN JAPAN) |
Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.
Q: What can the GS-607 series measure?
A: It'sNot for hardnessYes, but for inspectionThe hard meter itself.%After the hardness count is loaded in a folder, the assigned weight is applied with 3 base hammers, confirming the scale plate 25, 50, and X-rays. The accuracy of the 75 three points (permissible error ZQ4) is indicated.sSecretation. Reference: 1
Q: Why does a hard meter need to be tested?
A: The hardometer is a test machine that is managed according to the system's requirements under the ISO 9001 (JIS Q 9001) system for "watch machines" and "check machines". The weight of the spring charge is the basis for the hardness reading of the rubber - the signal is shifted in its entirety if the spring power changes. the official recommends periodic checks according to the frequency of use. The method of checking "the power of spring" is the GS-607 series., which is used to explain the "power of spring" in the context of the use of attention
Q: What kind of a hard-to-do?
A: corresponds to the matching hard-meter type usedGS-607:GS-701N / GS-701G / GS-706N / GS-706G;GS-607A:GS-709N / GS-709G;GS-607B:GS-719N / GS-719G / GS-721N / GS-721G / GS-750G / GS-753G;GS-607CGS-743G. The four types are of 3.7kg. If not, please inform the hardometer model to be confirmed with cloud help
Q: Can digital hardometers (GSD series) be checked?
A: No. This is not the caseCould not calibrate digital hardscales%1%2%2,And he couldn't fix his product.!!The home machine applies to the application of the spring charge value for the pointer (simulating) hardmeter.ScreaksScreamsS
Q: Does Type D hardmeter have a tester?
A: Officially specifiedTester not to produce rad D hardmeter%2The exact weight confirmation for the Type D hard meter is consulted separately
Q: What else should we check, besides the weight? Q
A: The official periodic section on "Use of Attention" lists three -111111111111111111111111111111Pressured needle height(In a free state, the pointer should mean 0; plus, the face should be hard and smooth, and the pointer should be 100 + 0/-1; oo D, be careful not to deform the pin's tip;2 22222222Pump shape%(A tool microscope to confirm whether the cutting size and shape are within the acceptable value of the specifications and that wear or injury require a replacement of the presses)The strength of springs.!!(i.e. the project in the GS-607 series). The pressure pin height can be checked with a separate high-level pin ZY-119/ ZY-120
Q: Can you provide a proof of correction?
This page does not include an official calibration cycle.Fun_w._Fun_w_w_w
Q: Is the hard scale attached to the photograph? Q
A: No. —Hardness in photos is a separate product.!!this page provides only the body of the testerGuangzhou Yunke Electronics Co., Ltd.A tester and a hard meter match can be provided and call advice is welcome.!!
Official Positioning Note: TECLOCK TECLOCK hardmeter tester is TECLOCK (TECLOCK) hardmeter tester (Red charge heavy checker) This machine is a simple spring weight checker for analogue hardometers, which are used for routine inspections and periodic points: when hard meters are refilled with a clamp, the specified load is applied with 3 base hammers. Confirm the correct instructions for the three points of the tc 25, 50, 75 (permissible error 1). Another way to do this is to use the upper-stenian facility to get the hard meter to be checked. the hardness of the plant, which is extra-doctor-type (digital), and other products cannot be corrected by the home. TECLOCK (TECLOCK) is a Japanese conglomerate of flexible hardness measuring machines, and the tester for the Type D hardness meter is not officially produced. The product lines are JIS K 6253, JIS K 7215, JIS K 7312, JIS S 6050, JIS S 6050.Scope, and the product lines are based on JIS K 6253, JIS K 7215, JIS S 6050., JIS S 6050..s, JIS K 7312, JIS S 6050.s Standard division of JIS K 6301, ASTM D 2240, ISO 7619/ ISO 868 covers all hard areas from supersoft bubbles to hard plastics. Reference: 1950
Option hint: This page is a hard-metered spring weight checker, and the hardness in the photograph is measured as an alternative to the sale of the parts, and a separate purchase of the GS-/GSD- series of hard-meters is required for use according to the type of material being measured. -SertGuangzhou Yunke Electronics Co., Ltd.The supply of TECLOCK is complete with hard-metered spring weight examiners and hard-meters, and the caller is welcome to be selected and matched
All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.
For a quotation, lead time or an optional calibration certificate, please contact our engineers.