AND MS-74A Electronic Balances (Model MS-74A) is a Electronic Balances supplied by Guangzhou Yunke Electronics Co., Ltd. AND MS-74A Electronic Balances — Electronic Balances · Yunke Electronics. Request a quotation and datasheet.
Brand: AND | Category: Electronic Balances
Sales Inquiries: 15626018696 · 78403603@qq.com

| Model | MS-74A |
|---|---|
| Series | A&D MS / MX / MF / ML-A Series |
| Category | Thermal Type Water Division Measurement Instrument (Thermal Type Water Division Measurement Instrument, 400 W Lamp Height plus Thermal) |
| Brand / Origin | A&D(JapanAND / A&D Company, Limited) |
| Official Series Positioning | Heat-Drying Moisture Analyzers |
| Reading Range of This Series | 0.001% / 0.01% / 0.1% / 0.01% / 0.1% / 0.05% / 0.1% / 1% / 0.1% / 1%(Official model list for this series) |
| Temperature Range (Sample Disk ) | 30 to 200 °C (1 °C increments) |
| Plus Thermal Mode | Standard heating, Ramp heating, Step heating, Quick heating |
| Measurement mode | Standard mode, Timer mode, Custom mode |
| Meter Calculation Unit | Moisture content based on wet weight, Moisture content based on dry weight (Atro), / Solid content, Ratio, Gram |
| Can Measure Sample Mass Range | 0.1 to 71 g |
| Mass Readability | 0.0002 g |
| Weight (Sample Mass) | 0.05% |
| Sample Disk Dimensions | Ø90 mm |
Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.
The following table is the official specification of MS-74A, the data being taken from the specification table of the series of pages of the A&D Japanese Official Network, without conversion or rewriting
The following table shows the full number and key parameters currently on sale in the official A&D MS/MX/MF/ML-A series, which is marked to facilitate horizontal comparison of volume and reading
| Model | Maximum Capacity | Readability (Graduation) |
|---|---|---|
| MS-74AT | ||
| MS-74A | ||
| MX-53AT | ||
| MX-53A | ||
| MF-53A | 0.001% / 0.01% / 0.1% | |
| ML-53A | 0.01% / 0.1% / 0.05% / 0.1% / 1% / 0.1% / 1% |
Q: What are the readings (points) of MS-74A?
A: The official specification table gives a reading (d by fraction) of 0.0002 g, the maximum measure is given in the specification table. The double-degree model gives two readings, and the high-precision series is valid only in a smaller section. Reference: MS-74A
Q: What is the advantage of the hydrometry device over the baker?
A: Thermodry water spectrometer (halogen lamps heating + built-in scales) can provide results within minutes to 10 minutes, without chemical reagents and showing dry rates in real time; the bakery process takes longer but applies standard methods. The official RSTemp function quickly determines the recommended dry temperature
Q: What about A&D and DeAnte, SETRA scales?
A: All three brands cover between one and one in 10,000: A&D is the most complete model on micro- and semi-minimum (0.001 mg ~ 0.01 mg) and built-in calibration machine models. Q1 Also have unique features such as ISD impact detection, ECL electronic control load; the technical precision of the DeAnte ES series; and SETRA primary value for money. The selection remains in order of magnitude. Readers and calibrations are on the basis of the number of readings.!
Q: Can this scale be used for density measurements?
A: Most A&D analysis/ precision skyband ( + hook) for density and weighting with official density measurement components (e.g. AD-1653/ AD-1654); The applicability of specific accessories to MS-74A is based on the official list of selected accessories
Q: How often does it take to calibrate?!?
A: It is recommended that verification be performed during the use of frequency and environment: the type of machine with built-in calibration codes can be automatically calibrated on a daily or per start-up basis; the external calibration type needs to be extra coded. Officially, minimum volume and duplicate verification functions are provided. The cycle can be created by the GLP/GMP requirement
Q: Is the product picture the official original?
A: An official original, but not a separate product. A&D officially provides a series of product photos, and the official product of the A&D MS/MX/MF/ML-A series is shown on this page. Standardised white bottom with watermarks, as per the official original. Model differences are in the sign and specification parameters, as shown in the specification table on this page
Q: Can data be exported or printed??
A: Yes. A&D scale with RS-232C or USB interfaces to support GLP/GMP/GCP/ISO compliance output, connecting official printers such as AD-8129TH, Or export to a computer via the lanCT series.!
Q: How do you confirm the offer and the period of submission?!
A: The price is not officially marked on a public page. Please contact the salesman of Guangzhou Yunke Electronics Co., Ltd. to confirm the price, spot and delivery of MS-74A; the price is not displayed on this page
Q: Are calibration certificates provided with the goods? Q: Q
A: Standard configuration usually does not include a third-party certificate. If you want to check a certificate/calibration certificate or a certificate from the Institute of Metrology, please specify at the next list that we can arrange it
A&D officially provides product photos in series, consistent with a series of different models, so this page is an official product picture of the series, with variations in model numbers on the specification parameters of the model, volume and readings. Please refer to this page specification table. Pictures are standardized for the white bottom and watermarked as originally prepared and not replaced by a crowned plume.ScrewScreechSceneSc
All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.
For a quotation, lead time or an optional calibration certificate, please contact our engineers.