Mitutoyo 468-971 Measuring Tools (Model 468-971) is a Mitutoyo Measuring Tools supplied by Guangzhou Yunke Electronics Co., Ltd. Mitutoyo 468-971 Measuring Tools — Mitutoyo Measuring Tools · Yunke Electronics. Request a quotation and datasheet.
Brand: Mitutoyo | Category: Mitutoyo Measuring Tools
Sales Inquiries: 15626018696 · 78403603@qq.com

| Brand / Origin | Mitutoyo Mitutoyo(JapanMitutoyoMitutoyo / Mitutoyo Corporation,Japan) |
|---|---|
| Series | Mitutoyo 468 Series Digimatic Holtest three points Type Inside Micrometers |
| Order No. | 468-971 |
| Main Unit Model | HTD-12RST |
| Set Installed Type | Interchangeable Head sets Installed ( Type sets Installed, total a units Display Device) |
| Measuring Range | 6 - 12 mm |
| Resolution | 0.001 mm |
| Reading Method | Digital, digits Height 7.5 mm |
| Measuring Surface | three Measure , Coating Processing |
| Automatic | three points Type 120° Measure , Automatic Setting Reading Internal Diameter Value |
| IP Rating | IP65(can at Environment Operating) |
| Measure Length Welding Systems | ABS( to Measurement)/ INC(Phase to Measurement) Dual Welding Systems |
| Preset Value | Storable 2 groups |
| Data output | with Measurement Data Output Terminal |
| Other functions | Functions Setting, Low Voltage Alarm, HOLD, Approx. 20 minutes No Operation Auto Power-off |
| Power Supply | SR44 Battery × 1, Normal Gauge Operating under Service Life Approx. 1.2 years |
| Matching Setting Ring Gauge | ø8, ø10 each 1 pcs |
| Matching Extension Rod | 100 mm(1 pcs) |
| Deep Hole / Blind Hole | optional with Extension Rod Measure Depth Hole; Measure can Blind Hole Bottom Surface Measurement |
| Warranty | Subject to terms of sale |
Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.
This article is a Mitutoyo package, cargo numberS-H-H-H-H-H-. Reference: 468468-971Host typeScrewScHTD-12RSTmeasure rangeScreen6 - 12 mmThe set isResizeable suite (economics suit, shared one display)A display device is shared throughout the entire section, and the replacement of the header will cover the entire area of 6-12 mm, which is an economic configuration that balances costs with coverage
The following parameters are derived from the official catalogue of Mitutoyo Mitutoyo, which was not converted or rewritten; the maximum permissible error (MPE) data for this series are not officially provided and therefore not included in the table
This package is configured according to the following lists and is independently packaged for standard plant fittings
This package covers6 - 12 mmThe small aperture area is the smallest in the 468 series. The full coverage was achieved by replacing three of the headers (6 - 8 / 8 - 10 / 10 - 12 mm). coverage of the headlines is not possible. / 86 / 10 — 12 mm A display device is required. A aperture test for small precision parts, hydraulic gas components, jet mouth holes, small bearings, etc. 12 mm..Aperture test for small precision parts, hydraulic gas components, spray mouth holes, small bearings, etc.12 mm
The 8, 10, and the 10 are two sets of rules. The opening of the boxes will complete zeroing if the baseline correction is required for the 8 - 10 mm and 10 - 12 mm respectively
Mitutoyo (Mitutoyo) 468 Series biiq 200hriiitiiqThree-point inner perforated 1,000-foot (three-point aperture 1,000-foot)Three radiant silicons are all clothed by 120°, which can be measured automatically with a cavity in the hole, and the true value of the inner diameter is read directly, and the readings are not dependent on the operator's hand and position; compared to the two-point inner diameter device, It is more insensitive to the installation angle and the results of multiple measurements are more stable and suitable for precision aperture tests of the required radians and cylindricals
For this seriesLCD count readings%%%%character height 7.5 mm, read intuitively avoids the difference in vision and estimation error caused by mechanical typographical readings
Two-point inner diameter devices need to look for maximum values for collusive collage inside the hole, and the results are easily influenced by the operator's manual approach; the three-point structure is designed to be three-point silicons and contact walls simultaneously, and the contact link is necessarily through the hole centre, so that one time it is set for a determination. Repetitious and efficient, especially for bulk aperture detection and rapid field determination
Watch out for the selection.!The accuracy of measurements cannot be changed using a survey beyond the mark, and there is no official guarantee that the measurements will be accurate at this time. select the matching package between the measured aperture zones and do not mix the head
Specifications: Guangzhou Yunke Electronics Co., Ltd. Mitutoyo 468. Please contact our engineers for the full technical wording.
All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.
For a quotation, lead time or an optional calibration certificate, please contact our engineers.