Case 1 — Opening-torque sampling on pharmaceutical oral-liquid bottles
- User: A medium-sized oral-liquid manufacturer producing about 100,000 ampoules per day
- Test object: 10 ml amber glass oral-liquid bottles with aluminium-plastic combination caps; nominal opening torque 0.8~1.2N・m
- Test procedure:
- Randomly select 30 finished bottles from each batch and centre each one in the TNJ-2 fixture
- Tighten the clamping pins to hold the bottle, then turn the cap anti-clockwise by hand
- Read the peak opening torque and compare it with the specified range
- Why this model: The TNJ-2 has a 2N・m capacity and 0.001N・m resolution, which covers the 0.8~1.2N・m opening-torque range exactly. No PC data export is needed for on-the-spot line sampling, and the purchase cost is about 30% lower than the TNP-2
- Result: The rate of non-conforming cap opening force fell from 2.3% to 0.5% and customer complaints dropped by about 70%; sampling time per batch fell from 15 minutes to 8 minutes
Case 2 — Closing-torque inspection of cosmetic sample jars
- User: A contract manufacturer for a domestic cosmetics brand, producing travel-size creams and sample serums
- Test object: 5 g / 10 g sample cream jars with plastic screw caps; specified tightening torque 0.5~0.8N・m so that caps do not loosen in transit
- Test procedure:
- Operators cap the jars with an electric capping machine at the specified torque, then re-check with the TNJ-2
- Read the peak tightening torque in the forward direction and the peak opening torque in reverse
- Test 5 samples at the start and 5 at the end of each shift
- Why this model: Sample jar caps generate very little torque (<1N・m), which is below the useful accuracy of a high-capacity instrument. The TNJ-2 combines a small capacity with high resolution and simple manual operation, so non-specialist line inspectors can use it
- Result: Leakage complaints during transport fell by 60%, and capping-machine settings are now adjusted against measured values rather than operator feel
Case 3 — Cap-seal torque verification on supplement bottles
- User: A dietary-supplement manufacturer bottling softgel and hard-shell capsules
- Test object: 60-count HDPE plastic bottles with tamper-evident screw caps; specified opening torque 0.6~1.0N・m
- Test procedure:
- The packaging line uses the TNJ-2 to monitor the automatic capping machine
- Sample 5 bottles every 2 hours and record the peak opening torque
- Adjust the capping machine's torque spring as soon as drift is detected
- Why this model: Supplement bottles mostly use low-torque plastic caps, well within the TNJ-2's accuracy. Its economy price suits a unit kept permanently on the shop floor without a dedicated operator
- Result: Capping-machine parameters became noticeably more stable; stripped threads and cracked bottles caused by over-tightening were largely eliminated, and customer reports of "caps that won't open" fell by 80%
Case 4 — Cap torque on pharmaceutical ointment tubes
- User: A manufacturer of topical medicines producing 10 g / 20 g aluminium-plastic laminate tubes for dermal ointments
- Test object: Flip-top / screw caps on ointment tubes; specified opening torque 0.3~0.6N・m
- Test procedure:
- Place the finished tube in the TNJ-2 fixture and adjust the pins to hold the body
- Turn the cap and read the peak opening torque
- Run comparative tests across different batches of cap material
- Why this model: Ointment tube caps produce very low torque, and the TNJ-2's 0.001N・m resolution resolves the differences clearly. The lack of on-board data storage does not affect spot checks on the line
- Result: A supplier with a better-performing inner plug thickness was identified, and opening feel became markedly more consistent from batch to batch
Case 5 — Screw caps on small food sauce bottles
- User: A small condiment producer making miniature jars of mustard and salad dressing
- Test object: 50 g glass jars with plastic screw caps; specified opening torque 0.8~1.5N・m
- Test procedure:
- Routine laboratory sampling, 10 jars per batch
- Verify cap seal performance and opening feel at the same time
- Why this model: On a limited budget the user only needed an on-the-spot pass/fail reading, not PC-generated reports. The TNJ-2 is cost-effective and requires no operator training
- Result: Cap torque standards were established before the line went into production, volume production stayed stable, and the complaint rate was held below 0.1%
Case 6 — Tightening torque of vape pods / atomisers
- User: A contract manufacturer of vaping devices, making disposable and replaceable-pod atomisers
- Test object: The thread connecting the pod to the battery unit; specified tightening torque 0.4~0.7N・m
- Test procedure:
- Keep a TNJ-2 beside the assembly station on the production line
- Every hour, sample finished units and unscrew them by hand to read the peak value
- Verify that the automatic screwdriving equipment still meets the torque specification
- Why this model: Precision low-torque testing is within the TNJ-2's accuracy, and the unit can be used hand-held or bench-mounted, so it moves easily around the workshop
- Result: Pod leakage fell and stripped threads became less frequent; the assembly station now works to a quantified torque standard
Additional selection guidance
All of the cases above share the same profile — low torque, on-site sampling, no need to archive data — which matches the economy positioning of the TNJ-2. If instead you need:
- PC data export for ISO9001 quality records → choose the TNP-2
- Torque above 2N・m → choose the TNJ-5 / TNP-5
- High torque on large drums and pails → choose the TNJ-10 / TNP-10