MOTIVE MTF-200N Force Gauges (Model MTF-200N) is a Force Gauges supplied by Guangzhou Yunke Electronics Co., Ltd. MOTIVE MTF-200N Force Gauges — Force Gauges · Yunke Electronics. Request a quotation and datasheet.
Brand: MOTIVE | Category: Force Gauges
Sales Inquiries: 15626018696 · 78403603@qq.com

| Model | MTF-200N |
|---|---|
| Series | MTF |
| Sensor Type | built-in Sensor a Body Type (Height Accuracy Type) |
| Range | 200N(Approx. 20.4 kgf) |
| Displayed Value | 200.00N (20.000 kgf) |
| Resolution | 0.02N (0.002 kgf) |
| Accuracy | Official Positioning is Height Resolution Height Accuracy Type, Maximum Resolution 0.0001N Quantity class; Tool Body Difference by Supplied Check is Standard. |
| Main Unit Dimensions | Main unit and MTM / MTA / MT Same Flat units (176 × 74 × 29 mm) |
| Sampling Rate | 1000 times / s (MTM / MTA / MTF is 2 kHz) |
| Overload Capacity | 200% Full Range |
| Memory Functions | 1000 pcs Data Quantity Value |
| Data output | RS232C / USB / Analog -2~+2V / Comparison Signal |
Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.
MOTIVE Taiwan MOTIVE QMTF-200NSpecifications: MOTIVE 200N 200.00N 20.000 kgf 0.02N 0.002 kgf 2N 0.0002N 2 kHz 15 kHz 5 MTF KN. Please contact our engineers for the full technical wording.
| Model | Range | Displayed Value | Resolution | Equivalent kgf | Equivalent British_Equal British |
|---|---|---|---|---|---|
| MTF-2N | 2N | 2.0000N (200.00 gf) | 0.0002N (0.02 gf) | 203.9 gf | 7.19 ozf |
| MTF-5N | 5N | 5.0000N (500.00 gf) | 0.0005N (0.05 gf) | 509.9 gf | 1.124 lbf |
| MTF-10N | 10N | 10.000N (1.0000 kgf) | 0.001N (0.0001 kgf) | 1.02 kgf | 2.248 lbf |
| MTF-20N | 20N | 20.000N (2.0000 kgf) | 0.002N (0.0002 kgf) | 2.04 kgf | 4.496 lbf |
| MTF-50N | 50N | 50.000N (5.0000 kgf) | 0.005N (0.0005 kgf) | 5.1 kgf | 11.24 lbf |
| MTF-100N | 100N | 100.00N (10.000 kgf) | 0.01N (0.001 kgf) | 10.2 kgf | 22.48 lbf |
| MTF-200N | 200N | 200.00N (20.000 kgf) | 0.02N (0.002 kgf) | 20.4 kgf | 44.96 lbf |
| MTF-500N | 500N | 500.00N (50.000 kgf) | 0.05N (0.005 kgf) | 51 kgf | 112.4 lbf |
| MTF-1000N | 1000N | 1000.0N (100.00 kgf) | 0.1N (0.01 kgf) | 102 kgf | 224.8 lbf |
Q: How do you choose the measure?
A: The nearest range is selected by the measured value of 1.5 ~ 2. This model size 200N (approximately 20.4 kgf) Resolution 0.02N (0.002 kgf), which recommends that the test force normally fall to the full mass of the 20% ~ 100%; If the measured force value is only below 10 per cent of the full range for a long time, it is recommended that a smaller level be changed to obtain a better and effective resolution
Q: What's the difference between MTF and MTM?
A: Resolution and sampling rates are two-level differences. The same is 2N, MTM showing 2.000N, resolution 0.001N,. MTF shows 2.0000N, resolution 0.0002N, higher than 5; The sampling rate for MTF valid 2 kHz may be expanded to 15 kHz and MTM for 2 kHz. The normal plug-in and pull-off with MTM is sufficient; MTF is selected for micro-changes that require the detection of the micro-changes in the form of ballistic motion, key-touching hand sense, fibre-optic microfibre
Q: When do you use the mN unit?
A: The measurement value is expressed in mN (mn cattle) in a more intuitive way than a decimal when it is below 1N, e.g. 0.0002N is shown as 0.2 mN. . XS XN MN ZXN ZX ZN ZXN ZX MTF supports N/ mN/ KN/ kgf/ gf/ lbf multi-unit switch
Q: How does the positive or negative peak test work?
A: When performing a compression - re-play type test (e. g. key press to release, connector insert to and pull), the positive peak records the maximum force of the thrust/ insertion direction, the negative peak records the maximum force of the return direction, A single clip will allow for peaks in both directions, without two measurements
Q: How does the 15 kHz sampling work?
A: The official indication of the effective sampling frequency is "up to 2 kHz, which can be extended to 15 kHz", the extension is for selection/ customization, and if there is a high frequency demand, please specify when ordering
Q: Can you use the automation?Assem
A: Yes. Except for the RS232C/ USB digital interface, Also available -2 ~ +2 V Simulation of voltage output and +NG / OK / -NG open arctic comparison signal (MAX Z) XXC 10 mA) The automatic up and downs and the eligibility determination can be made directly from PLC, which is accompanied by the electrodynamic power station. Reference: 30 V
Q: How does precision be called? Can it be traced?!!?
A: Officially positioned as a high resolution high precision with the highest resolution 0.0001N level of measure; specific offer based on random check of accomplishment. random check of accomplishment. Third party measurements are available for inspection in accordance with relevant protocols such as JJG; daily verification in the field can be performed using standard calculators or calibrated code matching.Scrells
Q: What should be the watchful side of daily usage?!?
A: 1 The force shall be directed at the sensor axis to avoid side-direction and bending; 2 Do not remain for long beyond 110 per cent and be discharged in time after warning; 3 Battery low voltage instructions appear and charged in a timely manner. Long-term absences should also be repeated at intervals;4 the environment is generally 0 ~ +40 °C, 20 ~ 80 % RH, avoiding condensation, Corrosionable gases and strong vibration environments;5 Regularly used standard gauges or coded verifications to maintain traceability.5
All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.
For a quotation, lead time or an optional calibration certificate, please contact our engineers.