NIDEC-SHIMPO FGS-250VC Force & Material Testing (Model FGS-250VC) is a Force & Material Testing supplied by Guangzhou Yunke Electronics Co., Ltd. NIDEC-SHIMPO FGS-250VC Force & Material Testing — Force & Material Testing · Yunke Electronics. Request a quotation and datasheet.
Brand: NIDEC-SHIMPO | Category: Force & Material Testing
Sales Inquiries: 15626018696 · 78403603@qq.com

| Model | FGS-250VC |
|---|---|
| Series | FGS-100VC / 250VC Type Motorised Measuring Force Instrument Dedicated pcs Stand (NIDEC-SHIMPO New ) |
| Category | Measuring Force Instrument pcs Stand / Type Motorised Test units (Height Capacity Type) |
| Brand / Origin | NIDEC-SHIMPO( New , Japan New SHIMPO) |
| Drive Method | Motorised ( Type, Type ) |
| Meter Measure Load | 2500 N(250 kg) |
| Load | 2500 N(250 kg) |
| Speed | 10 ~ 400 mm / min(Operation Surface Plate Setting) |
| Stroke | 400 mm |
| Display Part | points LCD, with No. 4 digits |
| Display Contents | Shift Speed 10 ~ 400 mm / min / Shift Distance 0.0 ~ 400.0 mm / Repeat Times 0 ~ 9999 |
| Mode | MANU Mode (Shift to Limit digits ) / JOG Mode () / SING Mode (Limit digits Single times Shift ) / CONT Mode (Limit digits Shift ) / PROG Mode (5 points Position Shift ) |
| Communication | USB(Connection Electric Use) |
| Matching Software | FGT-VC Dedicated Communication Software (USB to , Official website under ); can Output and Distance Data and Display Wire, with Trigger Functions (up to to Setting Load Rear Open Number), Continuous Number Times Setting, Hi / Lo Limit Judgment |
| Overload Input | Connection FGPX(FGP) Overload Signal and |
| Measurement Unit | 150 × 200 mm |
| Operating Temperature Range | 0 ~ 45 ℃(non-condensing) |
| Power Supply | AC100 V ±10% |
| Mass | Approx. 65 kg |
| Can Installation Measuring Force Instrument | FGP-0.2 ~ 50、100 / FGPX-0.2 ~ 50、100 / FGPX-250H |
| Supplied Accessories | Power Cable, FGPX(FGP) Use Connection Wire, USB Wire |
| Other | Measuring Force Instrument Use Power Supply AC Base, Open |
| Product image | Official Product Diagram (FGS-100VC and FGS-250VC is Same a Official records , Official total Use Same a Diagram) |
| Notes | Unit units is plus Unit , Force Value by optional Measuring Force Instrument Reading Output; Actual can Measure Load Upper Limit by Installed FGP / FGPX Rated Capacity is Standard. |
Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.
Applies to samples of electronic components, connectors and beams, key and switch, springs, rubber and plastics, film and glue, packaging and paper, hardware, textiles and wires, etc., stretching, compressing, stripping, plugging, bending, etc. The damage and the glue-strength test is used to impose a stable, consistent payload. Develops validation and control tables. The platform itself is the loading agency with the power values read out by the series of NIDEC-SHIMPO FGP/ FGPX/FGJN
NIDEC Officially placed FGS-250VC under the same product entry as FGS-100VC and shared the same official product photograph (the difference is in the way they look, in the type and capacity, speed, The image on this page is the official original of the purpose of the item, which is standardized and watered with a white bottom, without replacing the name of the crown, and the model difference is as shown in the specification table on this page
Q: FGS-250VC and FGS-100VC
A: Selected according to the maximum test strength required. FGS-250VC measured weight 2500 N (250 kg), mass approximately 65 kg; FGS-100VC measured charge weight 1000 N (100 kg), mass approximately 63 kg. The two processes are 400 mm,, and XX. The test stand is 150 x 200 mm, the speed is 10 ~ 400 mm/min, the speed of which is not the same as the speed of the 10 ~ mm/min, the speed of which is the same as the speed of the 10, the speed of which is the same as the speed of the 400, the speed of the ZX The difference is only between the volume and the high-test gravity instrument (250 VC, which is equipped with FGPX-250H)
Q: What kind of a detector is 2500 N?
A: Officially marked FGS-250VC can install FGP-0. 2 — 50, 100 and FGPX-0. 2 — 50, 100, plus FGPX-250H high-charge gravity instrument. X-Tracturing-Tractile X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X For a full 2500 N, a FGPX-250H must be attached; if only 1000 N, a FGPX-100 should be used. Reference values: 0.2.
Q: Can you get the data directly into the computer?!?
A: Yes. The platform has a USB interface, which is accompanied by a dedicated official FGT-VC communication software (free download by the official network) that will synchronize the load with the movement data into the computer and draw a curve; Software supports the trigger function (starting to take numbers after reaching the set weight), setting number of consecutive takeouts and determining the upper and lower limits. Randomly attach a USB line._Back
Q: The platform contains no ogres and treats?
A: None. The platform is a loading agency with a power value read by the monitor and the device is selected in the sample shape. Only the power line, the detector link and the USB line are randomly attached..ScreechScreenScreech
Q: Is the product picture the official original?
A: NIDEC Officially placed FGS-250VC under the same product entry and shared the same official product photograph (both look identical, the difference is in the sign type and capacity, speed, speed, etc.) The image on this page is the official original of the purpose of the item, which is standardized and watered with a white bottom, without replacing the name of the crown, and the model difference is as shown in the specification table on this page._._._._._. Reference: FGS-100VC
Reference values from the original datasheet: 0.2.
All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.
For a quotation, lead time or an optional calibration certificate, please contact our engineers.