DENSO BTG-2 Belt Tension Gauge (Model BTG-2) is a Tension Meters supplied by Guangzhou Yunke Electronics Co., Ltd. DENSO BTG-2 mechanical belt tension gauge, 100-1000 N (10-100 kgf), ±30 N accuracy, N/kgf dial, RESET zero, no battery required.
Brand: See datasheet | Category: Tension Meters
Sales Inquiries: 15626018696 · 78403603@qq.com

| Model | BTG-2 |
|---|---|
| Main Unit Number (Zero Part No.) | 95506 |
| Brand / Origin | Japan DENSO(Electric Installed / DENSO Corporation, Japan Control ) |
| Product Type | Pointer Type Mechanical Belt Tension Meters(Contact Type) |
| Measuring Principle | Spring Rod degrees Contact Type Force Measurement |
| Measuring Range | 100 ~ 1000 N(10 ~ 100 kgf) |
| Accuracy | ±30 N(±3 kgf) |
| Dial Minimum Scale | 10 N(1 kgf) |
| Display | Pointer Scale Dial, N / kgf Dual Unit Same |
| Zero Setting Method | Bottom Part RESET Zero Setting digits Knob |
| Applicable with | Unit Multi with, Same with, three Angle with etc. with (Approx. 100N or less with not Measurement) |
| Operation | T Type Protection Rubber , Single Setting Pressure |
| Housing Material | Oil Housing |
| Hook Material | Hardness Steel |
| Dimensions | Approx. 190 × 90 × 32 mm |
| Weight | Approx. 0.45 kg |
| Operating Environment | -10 ℃ ~ +50 ℃, Humidity 10% ~ 80% RH(non-condensing) |
| Power Supply | No requires Power Supply ( Mechanical Structure, not Operating Battery) |
| Optional Accessories | plus Length Rod 10040( Small Space Measurement); Accuracy Calibration Plate 10050 / 10051(Setting Verification Accuracy) |
| Supplied Accessories | Manufacturer Portable |
Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.
The DENSO BTG-2 (main unit part number 95506) is a mechanical, pointer-type belt tension gauge for checking the drive belts of automotive engines. The hook engages the belt, the operator applies steady pressure, and an internal spring deflects the belt; the pointer then indicates belt tension directly. It is a purely mechanical direct-reading instrument — no conversion, no batteries and no electronics.
The measuring range is 100–1000 N (10–100 kgf) with an overall accuracy of ±30 N (±3 kgf). The fan-shaped dial is graduated in both newtons and kilograms-force and has a smallest division of 10 N (1 kgf), so it matches the service standards of different vehicle manufacturers and resolves small tension differences. Because the reading is taken from a pointer, the gauge is particularly useful when the belt is partly obscured and a digital display cannot be watched directly.
DENSO Corporation (Japan) is a long-established supplier of automotive components and systems, and its mechanical belt tension gauges are specified as service tools by vehicle manufacturers — for example, the official repair manual for the Toyota 1NZ-FXE engine lists the DENSO belt tension gauge as the designated tool for drive-belt tension checks. Instrument dimensions are approximately 190 × 90 × 32 mm, weight approximately 0.45 kg, operating environment -10 °C to +50 °C at 10%–80% RH (non-condensing). A manufacturer's carrying pouch is included.
Tension checks and maintenance inspections of automotive engine drive belts — multi-rib belts, timing belts and V-belts — in dealership service workshops, repair shops, vehicle assembly quality lines and commercial-vehicle maintenance depots. Also used for periodic inspection of construction machinery and industrial drive belts, and for tracing belt-ageing noise faults.
Important: do not measure belts whose tension is clearly below approximately 100 N; doing so may twist the pointer and damage the internal gearing.
The specification table above lists the DENSO BTG-2 values cross-checked across several sources, with only consistent figures adopted; no values were converted or rewritten. This is a quotation-only catalogue; no prices are listed.
For selection advice, a demonstration, the optional extension probe 10040 and calibration plates 10050 / 10051, or a quotation and lead time, please contact our engineers.