Home › Products

Product Overview

Mitutoyo 7213A Measuring Tools (Model 7213A) is a Mitutoyo Measuring Tools supplied by Guangzhou Yunke Electronics Co., Ltd. Mitutoyo 7213A Measuring Tools — Mitutoyo Measuring Tools · Yunke Electronics. Request a quotation and datasheet.

Brand: Mitutoyo | Category: Mitutoyo Measuring Tools

Sales Inquiries: 15626018696 · 78403603@qq.com

Mitutoyo 7213A Measuring Tools

Technical Specifications

Order No.7213A
SeriesMitutoyo 7 Series Dial Depth Indicators(Dial Depth Gage)
Product TypeDial Depth Indicators(with Gauge Depth Scale)
Measuring Range0-210 mm
Graduation0.01 mm
Maximum Permissible Error±30 μm
Indicator Stroke30 mm
Measuring Force2.5 N or less
Base Size W63.5 mm
Base Size T16 mm
Base Flatness5 μm
Indicator Installation DigitSee the original manufacturer datasheet
Contact Pointwith Hardness Contact Point 21JAA225
Extension Rod3 pcs (30, 60, 90 mm)
Matching Indicator2952AB(Depth Indicator Use)
DisplayMechanical Pointer Type (No requires Battery, Pointer Continuous Indication Displacement )
Operating NotesExtension Rod Total Length Over Over 110 mm when Energy toward Operating (Contact Point under); Installed Extension Rod Rear Use Standard Gauge (such as Quantity ) Position Zero
Specification SourceMitutoyo Product Catalogue 2025-2026 No. 06-13 / Official D-67

Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.

Product Description

Mitutoyo7 SeriesA mechanical pointer depth indicator table suitable for the depth and range of holes, narrow ditches, without batteries, continuous swings of needles, and the sense of hand and readings of close to the public margin or head bottom7213ALong-range: measure range 0-210 mm, minutes 0.01 mm, signal error 30 μm, process 30 mm, base seat W=63.5 mm, T=16 mm, table of instructions installed at 1

The most confusing thing when selecting is the "range" and "protocol": 0-210 mm, , is expanded by the tagging longbar, while the instructions are a measurable journey. Reference: 7213A30 mmwith 3 root (30, 60, 90 mm). Base and measurement base level hardened, plane 5 μm; base leveled to the base of the worksheet, The poles are readable by vertical contact with the perforated

The difference in 7213A is concentrated on four points compared to the remaining 10 in the series: Baseline W=63.5 mm (decision distance and tiltability), Process 30 mm, A 30 μm for error values, a spherical header with a hard alloy 21 JAA 225. 7213A/ 7214A of 30 mm to the 0-210 mm at the cost of 30 μm, The detector is below 2.5 N; 7231A only has 5 mm, and X-rays are available in the following areas: However, the back-set pistons and the replacement of the header No. 21 JAA 226; The order of "pre-set base shape and distance" and then the required measure — and finally check the process error" is not always bought


The 7 series of pointer depth indicator tables are cross-referenced to the entire specification (a total of 11)

Order No.Measuring rangeProcessIndication ErrorBase WTInstallation ServiceTable of instructions
7210A0-1010±15 μm4016Specifications: 1. Please contact our engineers for the full technical wording.2902AB
7211A0-20010±15 μm63.516Specifications: 1. Please contact our engineers for the full technical wording.2902AB
7212A0-20010±15 μm101.616Specifications: 1. Please contact our engineers for the full technical wording.2902AB
7213A0-21030±30 μm63.516Specifications: 1. Please contact our engineers for the full technical wording.2952AB
7214A0-21030±30 μm101.616Specifications: 1. Please contact our engineers for the full technical wording.2952AB
7220A0-20010±15 μm10018Specifications: 2. Please contact our engineers for the full technical wording.2902AB
7221A0-20010±15 μm15018Specifications: 3. Please contact our engineers for the full technical wording.2902AB
7222A0-1010±15 μm16 (circle base)– (Round base) — — (Round base)Specifications: 1. Please contact our engineers for the full technical wording.2902AB
7223A0-1010±15 μm25 (circle base)– (Round base) — — (Round base)Specifications: 1. Please contact our engineers for the full technical wording.2902AB
7224A0-1010±15 μm40 (circle base)– (Round base) — — (Round base)Specifications: 1. Please contact our engineers for the full technical wording.2902AB
7231A0-2005±15 μm63.516Specifications: 1. Please contact our engineers for the full technical wording.1162A

Note: Full series fraction 0.01 mm, base level 5 μm; ø16/ ø25/ ø40 is circular base, without T dimensions. 40 The range of measurements is expanded by the length pole segment, which is not a single process in the table

III. Key Product Advantages

IV. Industries and Typical Applications

V. FAQ

Q: X 0-210 mm read once?. Reference: 7213A
A: The indicative schedule is 30 mm. 0-200/0-210 mm is expanded by the tagging of long poles, which are replaced by a standard rule (e.g. blocks) zero; The length poles are only vertically used when they have a length greater than 110 mm

Q: What about the 7213A and other 7 series models?
A: Bases for this paragraph W = 63.5 mm, Process 30 mm, Value Error 30 μm, Installed Location 1. 7210A / 7222A / 7223A / 7224A is a short mass of 0-10 mm (the last three paragraphs are circular bases); / 7223A / 7224A / X / / XV Q Q / ZX Q Q 7211A / 7212A / 7220A / 7221A / 7231A as 0-200 mm base; / 7221A / 7231A Q base Q 12Z Q Q / Z 7213A / 7214A is a long process for 0-210 mm. The base is selected from a workspace and then the depth selection process is sufficient

Q: Do you need a computer or data log?!?
A: The 7 series refers to a needle-based mechanical depth table, with no data output port, readings are manually recorded. If a piitik is required to export SPC/ measurement data network,_ The same door should be selected for the 547 series for the clear depth indicator table

Q: Can the head and long poles be changed?
A: The change of the size of the gauge will alter the movement of the base of the head relative to the base, the range of which may vary; the head diameter of the gauge is greater than the base aperture and cannot be installed; the change of plane / needle size will have to adjust the parallelness of the base base. Such needs are treated as special orders.!

Specimen source: Mitutoyo Commodity Catalogue 2025-2026 Page 06-13 (and check 06-14 Pages) PagesZZ Pag XZ Q Page Z XV Page 'm not sure.Ass Mitutoyo Chinese official, “Standard depth of 7 Series”, D-67, section E2025Platable G-6. Stamps Stamps Stamp of 7, E2025 Stamp Stamp of E2025 The product chart is a series of physical photographs of the Mitutoyo official catalogue, with base sizes based on the technical parameters of this page. Mitutoyo reserves the right to change specifications, based on random files from the factory..Screen. Reference: 7

All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.

For a quotation, lead time or an optional calibration certificate, please contact our engineers.

Related Products

Mitutoyo 7231A Measuring Tools
Mitutoyo Measuring Tools

Mitutoyo 7231A Measuring Tools

7231A
└ Dial Depth Indicators
Mitutoyo 7224A Measuring Tools
Mitutoyo Measuring Tools

Mitutoyo 7224A Measuring Tools

7224A
└ Dial Depth Indicators
Mitutoyo 7223A Measuring Tools
Mitutoyo Measuring Tools

Mitutoyo 7223A Measuring Tools

7223A
└ Dial Depth Indicators
Mitutoyo 7222A Measuring Tools
Mitutoyo Measuring Tools

Mitutoyo 7222A Measuring Tools

7222A
└ Dial Depth Indicators
Mitutoyo 7221A Measuring Tools
Mitutoyo Measuring Tools

Mitutoyo 7221A Measuring Tools

7221A
└ Dial Depth Indicators
Mitutoyo 7220A Measuring Tools
Mitutoyo Measuring Tools

Mitutoyo 7220A Measuring Tools

7220A
└ Dial Depth Indicators