ALGOL IT-50 Torque Testers (Model IT-50) is a Torque Testers supplied by Guangzhou Yunke Electronics Co., Ltd. ALGOL IT-50 Torque Testers — Torque Testers · Yunke Electronics. Request a quotation and datasheet.
Brand: ALGOL | Category: Torque Testers
Sales Inquiries: 15626018696 · 78403603@qq.com

| Model | IT-50 |
|---|---|
| Series | ALGOL IT Series Torque Calibration Instrument (JapanALGOL ALGOL) |
| Maximum Torque | 50 N·m |
| Measurement Range | 0.2 ~ 50 N·m(500.00 kgf·cm) |
| Minimum Resolution | 0.01 N·m(F.S. 50.00) |
| Degree | 1/5000 |
| Unit Switching | N · m, kgf · cm, lbf · in three Type Unit switchable |
| Accuracy | ±0.5% F.S. |
| Load | 200% F.S., with with Overload (O.L.) Protection Device |
| A / D | 16 bit |
| Sampling Rate | 640 / s |
| Than Device Functions | According to above, Lower Limit Setting, by LED and Buzzer Judgment Output |
| Maximum Memory Data | 511 groups |
| Output Signal | RS-232C(requires Dedicated Connection Wire HOP-RS), Mitutoyo Series Gauge Unit (HOP-FC Connection Wire), CENTRONICS(requires Dedicated Interface HOP-CE / HOP-FC) |
| Continuous operating time | Approx. 16 hours (Fully charged when, Operating Temperature 25℃) |
| Charging time | Approx. 12 hours |
| Supply Voltage | NiMH Battery, Pressure Device Charging Use Power Supply |
| Operating Conditions | Temperature 10℃ ~ 40℃, Humidity 85%RH or less (not can Condensation) |
| Dimensions | Body 150D × 230W × 60H mm; incl. Fixed Use Knob and Output Part 180D × 230W × 72H mm |
| Weight | Approx. 3300 g |
| Notes | IT-50 See at Official Body Version and , Text / Body Official website not Series; Measuring Range Value per 「20 × Minimum Resolution 」 Series Gauge 0.2 N · m. |
Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.
| Model | Maximum torque | Measuring Range | Minimum decomposition energy%2 | Resolution._Other Organiser_Other Organiser |
|---|---|---|---|---|
| IT-5 | 5 N·m | 0.02 ~ 5 N·m(50.00 kgf·cm) | 0.001 N·m | 1/5000 |
| IT-20 | 20 N·m | 0.2 ~ 20 N·m(200.0 kgf·cm) | 0.01 N·m | 1/2000 |
| IT-50 | 50 N·m | 0.2 ~ 50 N·m(500.00 kgf·cm) | 0.01 N·m | 1/5000 |
The typical test subjects include the tow set and point check of electric (bar) starters, the tow wrench and the tow starter.Stight set and point check. The caps and containers open to twist measurements, switches and spin buttons for operation torque tests, etc.. can be used for routine pointing of the production line, or for regular correction of the torque tool in the metering room or the product security sector
Q: What about the three slots in the IT series?
A: Select between the quantum of 20% ~ 80%, by the nominal torque of the measure tool.,..,..,., Twilight and point toggle settings for the little tox screwdriver to check IT-5 (0.02-5 N·m); conventional batch tox set, The caps open the torque measurements IT-20 (0.2-20 N·m); the larger torque selection IT-50 (0.2-50 N·m) is required. The three tranches are fully aligned except for the difference in the amount of the decomposition
Q: What is the difference between the IT series and the usual thin-swipe torque machine?
A: The IT series uses high accuracy, high unit value torque twitch sensors (Torque ion twig ) with good repeat accuracy, long life and no easy to overload damage; Many products on the market use thin-banded power sensors, to convert tots values by the multiplier of the force-arm conductor, low unit prices but with more uncertainty, high correction error and high risk of overload damage. —
Q: What are the objects that this instrument can measure?!?
A: In cases where "control only the torque, the torque angle" is used: torque and point the electric (bar) lift, torque wrench and torque daily check and correction, bottle caps to turn on the torque measurements, etc.A: torque and correct the torque of the torque, etc. to the torque, and then to the torque, to the torque of the torque, to the torque, to the torque It is a common configuration for the tow management and measurement room
Q: What's the top and bottom limit for?!??
A: The instrument may set a ceiling and a floor, respectively, and the measurements are determined by the output determined by the bee-beep with the LED light number on the panel (LOW / OK / HIGH tri-symposing instruction). / HIGH / HIGH The line operator can quickly determine eligibility without reading it.!?
Q: How do test data output and do statistics? Q
A: instrument provision of RS-232C interface (with dedicated connection HOP-RS) to the Mitutoyo (Mitutoyo) listwriter for statistical analysis (with HOP-FC connection); XX X-X-X-X-X-X-X-X There are also CENTRONICS parallel output (with a dedicated interface HOP-CE/ HOP-FC). The maximum memory of the 511 group measurements is available on the machine
Q: Battery Relay and Power?
A: NMMH batteries in storage, filled with electricity, which can be used continuously for approximately 16 hours (25°C) and charged for approximately 12 hours; or directly powered by transformers, It is suitable for use on site and can be brought to work on site.!
All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.
For a quotation, lead time or an optional calibration certificate, please contact our engineers.