Home › Products

Product Overview

CEDAR DI-12-SL4 Torque Testers (Model DI-12-SL4) is a Torque Testers supplied by Guangzhou Yunke Electronics Co., Ltd. CEDAR DI-12-SL4 Torque Testers — Torque Testers · Yunke Electronics. Request a quotation and datasheet.

Brand: CEDAR | Category: Torque Testers

Sales Inquiries: 15626018696 · 78403603@qq.com

CEDAR DI-12-SL4 Torque Testers

Technical Specifications

Measurement Range0.030~4.000 N·m
Accuracy±1%(499 digit or less ±5 digit)
Bit InterfaceHEX 6.35
Detection Part Dimensions60×155×80 mm
Detection Part WeightApprox. 290 g
DisplayLCD 4 Digits digits Display
Measuring DirectionCW-CCW(Right · Left Direction); Display is to Value, Data Output when with +(CW Direction)/-(CCW Direction)
Measurement ModeP-P(Peak, Hold Load Maximum Value, can Measure Torque and Torque)/T-R(, with Load Display)/P-D Judgment Mode (Judgment Output Torque and points, CW Direction)
Check JudgmentCheck Output Torque Value or points when Lamp points Indication (PD Mode when), Detection to Rear Electric Unit
Measurement Value Settingcan Setting Open Measurement (Judgment Calculation Open ) Torque Value
Real-time OutputPP · PD Mode under Measurement in per Fixed Interval Output Meter Measure Value, can Torque Wire, Use at Judgment Output Torque, points Torque, Torque
Data outputASCII division Type (Baud Rate 9600)
Power SupplyAC100V~240V
Auto Power-off10 minutes No Operation Rear Power Supply OFF
Cable LengthStandard 1 m(-L1), with 2 m(-L2), 4 m(-L4) optional
Display Part Dimensions166(W)×142(D)×48(H) mm
Display Part WeightApprox. 1 kg
Standard accessoriesBit (+○ #1, #2 or #0); Check , Calibration Certificate, can Property Body Series Diagram

Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.

Product Description

Product Overview

DI-12 series is CEDARSpunnersSlide out of torque detector%power-driven smooth twisting, with a green light when a slider (slip/lipter) or a yield point is detected and the.StightAuto Stopwhich is suitable for assessing the state of the screw link. In addition to the T-R model, there is a P-D decision model that allows for the determination of the torque and the point of submission. It also produces torque curves that can be used to determine the disruption, the limits and the yield torque.Stands. Reference: P-P

Application Scope

The determination applied to screw-sliding (sliptooth) torque, torque-dot and torque-breaking is often used for the limit assessment of the stifling mass

Key Features

Power drive, smooth

It stops automatically after the verdict. No need to retighten it

The torque value of the screw is measured

Generates torque curves (calculation of torque, limit to torque, yield to to torque, etc.)

Model 2 overwrite 1.5 mN m ersSpunnersSpuncutsSpunnersSpuntions. Reference: 4 N·m

Notes on Specification Terminology

The above parameters are itemized from the "se" table and the "supplier" of the official product specification PDF, which is not converted in units and is not extrapolated; This page is also not filled in for items that are not listed in the official specification form in the form "- ". Reference: CEDARDI-12-SL4) the series is DI-12-SL4/DI-12-SL02, and the difference item for other models in the series is shown separately in that model entry

Inspection and automatic stop

In P-D, when a tortoise or yield point is detected, the green light is activated and automatically stopped by the power, avoiding any further damage to the work; and the "start value" can be set. The starting point for determining the calculation of the calculation.!

Real-time output can be measured in a fixed-spacing output in PP/PD mode, which, in conjunction with the torque curve, analyses the tracks of slider, yield point torque and breaker torque._Bres_Tr_Tr_Tr_Tr_Tr_Tr_Tr_Tr_Tr_Tr_Tr_Tr_Tr_Tr_Tr_T

Two-type process and checkout

DI-12-SL4(a) The amount of the product is not available for the purpose of the control of the equipment; is not available for the control of the equipment. Z (a) Batch interface HEX 6.35, with the detection dimension 60×155, approximately 290 g, applicable to the conventional screws; XX . Reference: 4.000 N·m, 80 mm, 0.030, 1, 499, 5DI-12-SL02Volume 1.5 — 200.0 mN mm, Accuracy 2% (499 § 10 § § below) Batch interface 4 paid in half, check out 20, approximately 80 g for micro-poles. X x , The display department shares (166(W) x 142(D) x 48(H) mm, approximately 1 kg, cable standard 1 m, ,Scope X-Systems, X-Systems, X-Systems, X-Systems, X-Systems, X-Symbols 2 m/4 m is also optional. Reference: 145 mm

Standard Accessories and Ordering

Please indicate "CEDAR (CEDAR meter)+ model" when ordering, for exampleScretsScCEDAR DI-12-SL4The official pricing is not included on this page. Please contact Guangzhou Yunke Electronics Co., Ltd. for the price.Tppppp

FAQ

Q: What's a slip-out torque?.!?
A: The torque value of the nail that starts to slip (sliptooth) during the twisting process is an indicator of the limit state of the thread connection. The DI-12 series is designed to detect the torque, and automatically stops after detection, avoiding continued strength

Q: Can you detect the point of submission and break the torque? Q: Can
A: Yes. This machine supports the P-D decision mode (sliding tort and yield point) and real-time output, generating a torque curve that can be used to analyse slider torque, yield point to torque and break torque._Focus torque. toggler torque torque. torque. torque torque to break torque. tor

Q: How do you choose the two models?!!?
A: DI-12-SL4 for 0.030 4.000 N·m (HEX 6.35 batch interface) DI-12-SL02 is 1.5 ~ 200.0 mN.m. (4 in half), selected by screw specification and torque scale. ( 4 in half)

Q: Power and cable?
A: Power source AC100V — 240V, 10 minute unoperated automatic shutdown; cable standard 1 m (-L1) between the outlet and the display 2 m (-L2), 4 m (-L4) are also optional and specified upon purchase

All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.

For a quotation, lead time or an optional calibration certificate, please contact our engineers.

Related Products

CEDAR DI-12-SL02 Torque Testers
Torque Testers

CEDAR DI-12-SL02 Torque Testers

DI-12-SL02
└ CEDAR (Japan)
CEDAR CP-10 Torque Testers
Torque Testers

CEDAR CP-10 Torque Testers

CP-10
└ CEDAR (Japan)
CEDAR CP-1 Torque Testers
Torque Testers

CEDAR CP-1 Torque Testers

CP-1
└ CEDAR (Japan)
CEDAR NTS7-RT2 Torque Testers
Torque Testers

CEDAR NTS7-RT2 Torque Testers

NTS7-RT2
└ CEDAR (Japan)
CEDAR NTS7-RT05 Torque Testers
Torque Testers

CEDAR NTS7-RT05 Torque Testers

NTS7-RT05
└ CEDAR (Japan)
CEDAR WDI-10HR Torque Testers
Torque Testers

CEDAR WDI-10HR Torque Testers

WDI-10HR
└ CEDAR (Japan)