Home › Products

Product Overview

CEDAR CD-10M Torque Testers (Model CD-10M) is a Torque Testers supplied by Guangzhou Yunke Electronics Co., Ltd. CEDAR CD-10M Torque Testers — Torque Testers · Yunke Electronics. Request a quotation and datasheet.

Brand: CEDAR | Category: Torque Testers

Sales Inquiries: 15626018696 · 78403603@qq.com

CEDAR CD-10M Torque Testers

Technical Specifications

Measurement Range0.010~1.000 N·m / 1.0~100.0 cN·m
Accuracy±0.5% or ±0.002 N · m
Standard Accessories ( Model)Measurement Connection Head SJ-10 1 pcs; six Angle to Edge 5 mm Bit (4 pcs sets Installed)
DisplayLCD 3.5 Digits digits Display
Measuring DirectionCW-CCW(Right · Left Direction)
Measurement ModeTrack/Peak(Peak Hold)/Peak-Down( Peak Hold)/C(Real-time Output)
Pass/fail judgementper Setting Range Judgment (P-P Mode when); GOOD Lamp points /NG Lamp
Maximum · Minimum · AverageDisplay Memory Data pcs Number, Maximum, Minimum, Average
Real-time OutputApprox. per 1 / 180 s Output a times Load Torque
Data Storage800 records
Data outputASCII division Type (Baud Rate 19200); USB B Type Interface
Auto Power-off10 minutes No Operation Rear Power Supply OFF
Power SupplyNiMH Battery (with Over Charging Protection Circuit, Charging in Indication Lamp points )
Charging Time / Operating TimeCharging 3 hours / Continuous Approx. 12 hours Operating
Base Interface□20 / □9.5
Dimensions [Mm]160(W)×125(D)×55(H)
WeightApprox. 1 kg
Standard Accessories (Total )Dedicated Charger (Input AC100~230V 50 / 60Hz), Dedicated Case, Check , Calibration Certificate, can Property Body Series Diagram

Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.

Product Description

Product Overview

CD-100M/CD-10M is routinely checked for electric screwdriver by CEDAR counter (CEDAR).SpunnersStightStDigital tox tester (Twissometer)2026 was upgraded on the original basis: the display board shows the measurement mode directly, the unit of measurement is the maximum/minimum/average, and the unit is changed between N.m. and cN.m. Data storage from the original 300 toRule 800the real-time output cycle is accelerated from about 1/180 seconds to about 1/180 seconds, and the data output interface is changed to USB B. Quick-Time SamplesStamps Quick-Stamps Qualityssss Q X seconds QSs QSStances Q

Application Scope

Daily point and cycle check checks, mainly for the output torque of rotation tools such as electric screws, electric lifts and so forth, also apply to the test and abnormal determination of the stuttering tool on the stream line

Key Features

Show the "measuring mode" and "max. minimum. average"

Measuring units can be switched (N.m., cN.m., etc.)

Top- and bottom-limit set value to save the 5 group

Data storage 800 bar (old type 300)

Approximately once per 1/180 second in real time output%1%2%2%2Sec1 seconds%2Sec1

Data acquisition software can be downloaded free of charge

Overcharged protective circuits, lights are lit in charge.!

Data output as a USB B interface

Notes on Specification Terminology

The above parameters are itemized from the "se" table and the "supplier" of the official product specification PDF, which is not converted in units and is not extrapolated; This page is also not filled in for items that are not listed in the official specification form in the form "- ". Reference: CEDARCD-10M) the series is CD-100M/CD-10M, and the difference item for other models in the series is shown separately in that model entry

The mode of measurement and determination of the machine%

The machine supports four modes (real time tracking)/peak (peak maintenance)/Peak-Down (peak maintenance)/C (real time output); in P-P (peak-peak) mode, The determination may be made on the basis of a predetermined upper or lower range, and the determination shall be based on the followingGreen (GOOD)/red (NG)Hint, a fast-track screening suitable for batch-stressing operations

Memory data can be called and displayed for data numbers, maximum, minimum and average, allowing trend judgement to be made for a given batch of operations

Data Output and Software%

Data is exported in ASCII format (Portrate 19200), interfaced asUSB BCharlie_ClustersCthe instant load torque is exported about once per 1/180 seconds, which can be used to draw a torque wave. The official free data collection software downloads, which can directly import measurements into the computer for recording and statistics

Model differences and selection

Two models are two stages of the same type:!CD-100M(a) Volume 0.10 — 10.00 N·m (10 — 1000 cN.m.) suitable for medium to torque electric starters before and after M3CD-10MVolume 0.010 — 1.000 N·m (1.0 — 100.0 cN.m.) A fine start suitable for a small twist. The two shapes, power sources, displays are identical to data functions, only in volume, The absolute accuracy value is different from the attached calibration

Standard Accessories and Ordering

Please indicate "CEDAR (CEDAR meter)+ model" when ordering, for exampleScretsScCEDAR CD-10MThe official pricing is not included on this page. Please contact Guangzhou Yunke Electronics Co., Ltd. for the price.Tppppp

FAQ

Q: CD-100M and CD-10M
A: Select the amount within which the usual toxes are left: CD-100M over 0.10 — 10.00 N·m, CD-10M over 0.010 — 1.000 N·m.Screaks of the tow tows. to the tow to the to the to the to the to the to the to the to the to the to the to the to the to the It is recommended that the 1/3 — 2/3, which is commonly used for torque to be left in the process, be more readable in terms of resolution and determination of residual amounts._Stamps Stamps S /39XQs.s.sss

Q: What is the accuracy?!!?
A: Officially 0.5%, with absolute threshold: CD-100M is "0.5% or 0.02 N·m", 0.5 0.02 N·m CD-10M is "0.5% or 0.002 N·m" which is a more robust reading of the small torque paragraph. ZX or 0.002 N·m" — i.e., higher than the one in both. to the Tranglerss to the Trv to the Trangless to the Trangles to the Trangles to the

Q: Can you export data for record?
A: Yes. Data are exported in ASCII format via USB B interface, Portrate 19200, official free data acquisition software; The torque wave is recorded in conjunction with real-time output (approximately 1/180 once)

Q: How long can batteries last?
A: Officially required to charge 3 hours, used continuously for approximately 12 hours, with nickel hydrogen batteries, with recharge protection loops, 10 minutes without an operating automatic switch

All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.

For a quotation, lead time or an optional calibration certificate, please contact our engineers.

Related Products

CEDAR DI-12-SL02 Torque Testers
Torque Testers

CEDAR DI-12-SL02 Torque Testers

DI-12-SL02
└ CEDAR (Japan)
CEDAR DI-12-SL4 Torque Testers
Torque Testers

CEDAR DI-12-SL4 Torque Testers

DI-12-SL4
└ CEDAR (Japan)
CEDAR CP-10 Torque Testers
Torque Testers

CEDAR CP-10 Torque Testers

CP-10
└ CEDAR (Japan)
CEDAR CP-1 Torque Testers
Torque Testers

CEDAR CP-1 Torque Testers

CP-1
└ CEDAR (Japan)
CEDAR NTS7-RT2 Torque Testers
Torque Testers

CEDAR NTS7-RT2 Torque Testers

NTS7-RT2
└ CEDAR (Japan)
CEDAR NTS7-RT05 Torque Testers
Torque Testers

CEDAR NTS7-RT05 Torque Testers

NTS7-RT05
└ CEDAR (Japan)