CEDAR DI-9M-08 Torque Testers (Model DI-9M-08) is a Torque Testers supplied by Guangzhou Yunke Electronics Co., Ltd. CEDAR DI-9M-08 Torque Testers — Torque Testers · Yunke Electronics. Request a quotation and datasheet.
Brand: CEDAR | Category: Torque Testers
Sales Inquiries: 15626018696 · 78403603@qq.com

| Measurement Range | 2.0~800.0 mN·m / 0.20~80.00 cN·m |
|---|---|
| Standard Accessories ( Model) | Measurement Connection Head OW-025/OW-10 each 1 pcs |
| Accuracy | ±0.5%(Reading Value; 499 digit or less ±3 digit) |
| Display | LCD 4 Digits digits Display |
| Measuring Direction | CW-CCW(Right · Left Direction) |
| Measurement Mode | Track/Peak(Peak Hold)/Peak-Down( Peak Hold)/C(Real-time Output) |
| Pass/fail judgement | per Setting Range Judgment (P-P Mode when); GOOD Lamp points /NG Lamp |
| Maximum · Minimum · Average | Display Memory Data pcs Number, Maximum, Minimum, Average |
| Real-time Output | Approx. per 1 / 180 s Output a times Load Torque |
| Data Storage | 800 records |
| Data output | ASCII division Type (Baud Rate 19200) |
| Auto Power-off | 10 minutes No Operation Rear Power Supply OFF |
| Power Supply | NiMH Battery |
| Charging Time / Operating Time | Charging 3 hours / Continuous Approx. 12 hours Operating |
| Base Interface | □20 / □9.5 |
| Dimensions / Weight | 160(W)×125(D)×55(H) mm / Approx. 1 kg |
| Standard Accessories (Total ) | Thread Method ( Method 20×20×20, 5 Surface Thread Hole, Processing), Dedicated Charger (Input AC100~230V 50 / 60Hz), Case, Check , Calibration Certificate, can Property Body Series Diagram |
Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.
DI-9M-8/DI-9M-08 is CEDAR-DVSpunishmentSpIDSpunctionSpIDManual tools (twig screws, wrench)Digital torque tester. Compared to the CD series, the DI-9M series, the random hand-held tool for "cube-tube" of the tool, it can be directly checked by the hardwired torque of the tool. The display boards also support the visual display of the measurement patterns, the unit of measurement and the maximum minimum of the average of
The torque point check and cycle check, which apply to manual torque screws, wrench wrench, etc., are the basic torque management equipment
Show "measuring mode" "measuring unit" "max.m. average"
Measuring units to switch
Data Storage 800 bar
Approximately once per 1/180 second in real time output%1%2%2%2Sec1 seconds%2Sec1
Data acquisition software can be downloaded free of charge
A handheld device to determine the "Standed Cube" (5 face cothole)StightScreenStightSt
The above parameters are itemized from the "se" table and the "supplier" of the official product specification PDF, which is not converted in units and is not extrapolated; This page is also not filled in for items that are not listed in the official specification form in the form "- ". Reference: CEDARDI-9M-08) the series is DI-9M-8/DI-9M-08, and the difference item for other models in the series is shown separately in that model entry
The DI-9M series randomly attached the cube curing tool 20×20, which is a tool for the management of the cubes. Five-faced coils with different specifications (M2.6/M3/M4/M5/M6 or M1/M1.2/M1.4/M2/M3) Quest XC X/ The torque value can be read in close proximity to actual tightness and solve problems with manual tools that are difficult to interset. Reference: 20 mm
DI-9M-8(b) The volume 0.020 — 8.000 N·m (2.0 — 800.0 cN.m.) is a conventional torque with a OW-20/OW-60 calibrated interface; XXQ X; X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-XDI-9M-08Volume 2.0 — 800.0 mN mm (0.20 — 80.00 cN m) for microtangles with OW-025/OW-10 interface. X-X-X-X-X-Q X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X-X- The two-type homeform, power source and data function are consistent.!
Please indicate "CEDAR (CEDAR meter)+ model" when ordering, for exampleScretsScCEDAR DI-9M-08The official pricing is not included on this page. Please contact Guangzhou Yunke Electronics Co., Ltd. for the price.Tppppp
Q: Is DI-9M-8 and DI-9M-08 the same machine? Q: Q: Q: Question
A: The body is the same, with different scales from the attached one, and is the same series of two torque stylized files. 8 is 0.020 — 8.000 N·m, 08 is 2.0 800.0 mN.m., the magnitude difference 10 is multiple times the actual torque of the measure tool
Q: Can you detect a hand-to-hand wrench?
A: Yes. Randomly attached cubes are designed for manual tool determination; the five-faced device has different thread holes, which allow the proper aperture to be selected according to the tool to be used
Q: Precision and display?
A: Official specification is 0.5% (read value, 3 §, below § ) ScreaksA: Screw Screts Sp. Displays the number of LCD 4 bits, the plugin interface □ 20/ □ 9.5. Reference: 499
Q: How many pieces of data can be stored?!?
A: Data storage 800 strips and support for real-time output approximately once per 1/180 seconds, which can be recorded and recorded on computers in conjunction with official free software
All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.
For a quotation, lead time or an optional calibration certificate, please contact our engineers.