Home › Products

Product Overview

CEDAR DI-4B-25 Torque Testers (Model DI-4B-25) is a Torque Testers supplied by Guangzhou Yunke Electronics Co., Ltd. CEDAR DI-4B-25 Torque Testers — Torque Testers · Yunke Electronics. Request a quotation and datasheet.

Brand: CEDAR | Category: Torque Testers

Sales Inquiries: 15626018696 · 78403603@qq.com

CEDAR DI-4B-25 Torque Testers

Technical Specifications

Measurement Range0.30~25 N·m
Accuracy±0.5%(499 digit or less ±3 digit)
DisplayLED 4 Digits digits Display
Measuring DirectionCW-CCW(Right · Left Direction), Switching Open Selection
Measurement ModeTrack, Peak, Peak-Down(70 digit or more )
Auto Zero Time0.5~3.0 s (0.5 s Interval) Auto Zero; 0.0 s Setting is Manual Zero Setting
Counting DeviceMeasuring Range 0~99 ; Measurement Time 0.1~9.9 s; 2 digits LED Display (only P-P Peak Mode when Display)
Data outputUSB B Type, ASCII division Type (Baud Rate 19200)
Power SupplyNiMH Battery
Auto Power-off5 minutes No Operation Rear Power Supply OFF
Charging timeApprox. 3 hours
Operating TimeMaximum Charging when Continuous Approx. 8 hours
Battery Life300 times or more Charging
WeightApprox. 2.1 kg
Standard accessoriesHardness Connection Head (M10)/ Connection Head (M10) each 1 pcs; Sleeve Bit Adapter (6.35 HEX)/ Wrench Use Sleeve (to Edge 17 mm); Case; Dedicated Charger; Check , Calibration Certificate, can Property Body Series Diagram

Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.

Product Description

Product Overview

DI-4B-25 is CEDAR-DeepSmall shock tools, aerodynamic screws, high-out electro-snail bladesA digital tox tester for daily spot checks. Maximum detectable 25 N·m, built-in shock toolBlow-a-half countr (Blow-a-half)and can be measured directly in the case of a cylinder, showing the use of high brightness LED, with a clear reading in the dark

Application Scope

Daily point and torque verification applicable to shock-type tools such as small shock wrench, aerodynamic screws, high-out electrodynamic screws

Key Features

Maximum detectable 25 N·m

Internal shock tool counter with impact count%

It can be measured in the case of a cylinder

Highlights LED show that you can read clearly in the dark

Autocut (5 min inoperable)

Battery powered, easy to carry to the scene

Show automatic zero (sec 0.51, 0.0 seconds manual zero). Reference: 3.0. Reference values: 0.5.

Notes on Specification Terminology

The above parameters are itemized from the "se" table and the "supplier" of the official product specification PDF, which is not converted in units and is not extrapolated; This page is also not filled in for items that are not listed in the official specification form in the form "- ". Reference: CEDARDI-4B-25) the series is DI-4B-25, and the difference item for other models in the series is shown separately in that model entry

Strike CountCl

The shock class tool is built on a continuous strike to twist. A single peak does not represent the result of the operation. The built-in strike counter is measurable. Reference: DI-4B-250 — 99Strike, measure time0.1 9.9 secSpunnersdisplays 2 bit LED (only in P-P peak mode) to manage the "tangle value + number of hits ", closer to the actual operational status of the shock tool

Contact and attachment instructions.!

1 with M10 and M10 each: for hard connectionsScreaksScRigid%1Stiff (snail or bolt reaching full torque in approximately 1/10)ElastomerTight (approximately 3 to the Full Tox). In addition, a set of batch adapters (6.35 HEX) and a wrench can be used to directly load the drums (on the other side of 17 mm). QStight Quack QuackssStight Quasi

Standard Accessories and Ordering

Please indicate "CEDAR (CEDAR meter)+ model" when ordering, for exampleScretsScCEDAR DI-4B-25The official pricing is not included on this page. Please contact Guangzhou Yunke Electronics Co., Ltd. for the price.Tppppp

FAQ

Q: Why is there a strike counter?
A: The shock tool is a single blow, with a single single peak liable to be miscalculated. The strike counter can record the number of hits and the torque, and it can determine whether the tool has reached the target torque within the specified number of hits

Q: What is the difference between hard and soft?
A: Hard connectors for rigid hardened (approximately 1/10 to full twist) and soft connectors for flexible hardened (approximately 3 to convey full twists) show different performances for the two working conditions. Select the actual connecting object with 1 randomly

Q: Can you take the kit and take it?
A: Yes, this is one of the characteristics of the machine - it can be measured in the case of a kit, without having to deactivate the tool.!

Q: The margin of error?
A: Officially specified as 0.5 per cent (499 § 3 § § 0.30, as below). 25 N·m . ZX

All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.

For a quotation, lead time or an optional calibration certificate, please contact our engineers.

Related Products

CEDAR DI-12-SL02 Torque Testers
Torque Testers

CEDAR DI-12-SL02 Torque Testers

DI-12-SL02
└ CEDAR (Japan)
CEDAR DI-12-SL4 Torque Testers
Torque Testers

CEDAR DI-12-SL4 Torque Testers

DI-12-SL4
└ CEDAR (Japan)
CEDAR CP-10 Torque Testers
Torque Testers

CEDAR CP-10 Torque Testers

CP-10
└ CEDAR (Japan)
CEDAR CP-1 Torque Testers
Torque Testers

CEDAR CP-1 Torque Testers

CP-1
└ CEDAR (Japan)
CEDAR NTS7-RT2 Torque Testers
Torque Testers

CEDAR NTS7-RT2 Torque Testers

NTS7-RT2
└ CEDAR (Japan)
CEDAR NTS7-RT05 Torque Testers
Torque Testers

CEDAR NTS7-RT05 Torque Testers

NTS7-RT05
└ CEDAR (Japan)