CEDAR DID-05 Torque Testers (Model DID-05) is a Torque Testers supplied by Guangzhou Yunke Electronics Co., Ltd. CEDAR DID-05 Torque Testers — Torque Testers · Yunke Electronics. Request a quotation and datasheet.
Brand: CEDAR | Category: Torque Testers
Sales Inquiries: 15626018696 · 78403603@qq.com

| Measurement Range | 2.0~500.0 mN·m / 0.20~50.00 cN·m |
|---|---|
| Accuracy | ±0.5%(499 digit or less ±3 digit) |
| Display | LCD 4 Digits digits Display |
| Measuring Direction | CW-CCW(Right · Left Direction) |
| Measurement Mode | PP(Peak): Hold Load Maximum Value; TR(): with Load Real-time Display; PD(Peak under ): Hold Load by above to under ; C(Real-time Output): Approx. per 1 / 160 s Output and |
| Upper Lower Limit Setting | above · Lower Limit Value can at Measuring Range internal Setting, up to 5 groups |
| Pass/Fail Judgment Function | per Setting Range Judgment (P-P Mode when); GOOD Lamp /NG Lamp |
| Maximum · Minimum · Average Display · · Output | Display Data pcs Number, Maximum, Minimum, Average |
| Data Storage | Measured values Data 800 records |
| Data output | ASCII division Type (Baud Rate 19200); Output when requires with USB Wire ( B Type) |
| Auto Zero Time | 0.1~3.0 s (0.5 s Interval) Auto Zero; 0.0 s Setting is Manual Zero Setting |
| Key Zero Setting | per Clear Key i.e. can a Key Zero Setting Adjustment |
| Counting Setting | 1~99 times (per Direction Counting) |
| Power Supply | NiMH Battery (650 mAh) |
| Charging Time / Operating Time | Charging 3 hours / Maximum Charging when Continuous 10 hours |
| Auto Power-off | 10 minutes No Operation Rear Power Supply OFF |
| Bit Interface | φ4 mm |
| Weight | 180 g |
| Standard accessories | Bit #1(Single toward Use / Fixed Use each 1 pcs); Dedicated Charger; Check , Calibration Certificate, can Property Body Series Diagram |
| Part | Data Output requires with USB Wire ( B Type) |
Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.
DID-05 is CEDARSpunnersShow one-shaped digital tox knifeChanmass 2.0 — 500.0 mN.m., suitable for the very small torque screw to snap and torque confirmation. 4 mm, using a one-way (one-way clutch) structure, is rapidly advanced in the right direction; The top and bottom limit torque sets and uses a beeper and a LED tip, which contains a tight counter, and measures the 800 bar and supports real-time output
Microtangle stint work and torque confirmation applicable to precision screws and small electronic components is also used for production line stint numbers and eligibility determinations.?
Show one, lightly compactChannel
Data Storage 800 bar
Data Output is a USB Shape Interface
Sets the top and bottom limit to torque%1%2%2
Set value with beeper and LED hint
Built-in tight count%
Charged battery drive
Auto turn off. Operation rest
Support real-time data output%2%2%2
Wireless cable (no rope) type
Rolling clutches are used, right-wing direction (stretch) can be rapidly advanced
The above parameters are itemized from the "se" table and the "supplier" of the official product specification PDF, which is not converted in units and is not extrapolated; This page is also not filled in for items that are not listed in the official specification form in the form "- ". Reference: CEDARDID-05) the series is DID-05, and the difference item for other models in the series is shown separately in that model entry
Top and bottom limit values can be set in the range of measurements and can be saved at mostGroup 5.Step & & & QuestSdetermined in set range in P-P mode, with light cues: GOOD green, NG red. The built-in tight counter can be set1 — 99counting in a tight direction, to facilitate the operation of the flow line against error
The roller clutch is used to fast-track (right-wing) and automatically reset when unwinding, and is suitable for the operating rhythm of successive multiple screws; the batch interface is 4 mm, which allows for the replacement of the market-specific batch header
Data is exported in ASCII format (Portrate 19200), with a separate USB line (mini-B, for sale); Real-time output is about once per 1/160 seconds to record the torque changes in the stint process
Please indicate "CEDAR (CEDAR meter)+ model" when ordering, for exampleScretsScCEDAR DID-05The official pricing is not included on this page. Please contact Guangzhou Yunke Electronics Co., Ltd. for the price.Tppppp
Q: What is the occasion for DID-05?
A: Precision compaction and confirmation for the very small torque screw with a mass of 2.0 — 500.0 mN mm (0.20 — 50.00 cN m) Batch interface 4 mm.ScortationZX
Q: Can a qualified decision be made? Q
A: Yes. You can set the upper and lower limit value (maximum 5 group), determined in P-P mode, and with a bell signal. Reference: GOOD, NG
Q: How do you export data?
A: Data is exported in ASCII format, requiring a separate USB line (mini-B, sold); home-office data storage 800,. Approximately once per 1/160 second in real time.Spw_w_w_w_w_w
Q: Battery continuation?
A: Use of nickel hydrogen batteries (650 mah) charged 3 hours and maximum charge for approximately 10 hours; 10 minutes unoperated automatic shutdown
All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.
For a quotation, lead time or an optional calibration certificate, please contact our engineers.