Home › Products

Product Overview

CEDAR DID-4 Digital Torque Screwdriver (Model DID-4) is a Torque Testers supplied by Guangzhou Yunke Electronics Co., Ltd. CEDAR DID-4 display-integrated digital torque screwdriver, 0.020-4 N.m, +/-0.5%, HEX 6.35 mm bits, 800-data memory, 5 limit sets.

Brand: CEDAR | Category: Torque Testers

Sales Inquiries: 15626018696 · 78403603@qq.com

CEDAR DID-4 Digital Torque Screwdriver

Technical Specifications

Measurement Range0.020~4 N·m
Accuracy±0.5%(0.499 N · m or less ±0.003 N · m)
DisplayLCD 4 Digits digits Display
Measuring DirectionCW-CCW(Right · Left Direction)
Measurement ModePP(Peak): Hold Load Maximum Value; TR(): with Load Real-time Display; PD(Peak under ): Hold Load by above to under ; C(Real-time Output): Approx. per 1 / 160 s Output and
Upper Lower Limit Settingabove · Lower Limit Value can at Measuring Range internal Setting, up to 5 groups
Pass/Fail Judgment Functionper Setting Range Judgment (P-P Mode when); GOOD Lamp /NG Lamp
Maximum · Minimum · AverageDisplay Memory Data pcs Number, Maximum, Minimum, Average
Data StorageMeasured values Data 800 records
Data outputASCII division Type (Baud Rate 19200); Output when requires with USB Wire ( B Type)
Auto Zero Time0.1~3.0 s (0.5 s Interval) Auto Zero; 0.0 s Setting is Manual Zero Setting
Key Zero SettingMeasuring Mode under can a Key Zero Setting Adjustment
Counting Setting1~99 times (per Direction Counting)
Power SupplyNiMH Battery 1.2V×4 cells (800 mAh)
Charging Time / Operating TimeCharging Approx. 3 hours / Maximum Charging when Continuous 12 hours Operating
Auto Power-off10 minutes No Operation Rear Power Supply OFF
Bit InterfaceHEX 6.35
WeightApprox. 400 g
Standard accessoriesBit ○+ #1, #2; Bit Base; Single toward Bit Base; Dedicated Charger (Input AC100V~230V 50 / 60Hz); Check , Calibration Certificate, can Property Body Series Diagram
PartData Output requires with USB Wire ( B Type)

Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.

Product Description

The CEDAR DID-4 is the standard-torque model of the DID-4 series of display-integrated digital torque screwdrivers from Sugisaki Meter (CEDAR). It measures 0.020–4 N·m at ±0.5% accuracy (within ±0.003 N·m below 0.499 N·m) and uses a HEX 6.35 mm bit holder, so ordinary 6.35 mm hex bits fit directly. Upper and lower torque limits can be programmed in up to 5 sets, with a buzzer and LED signalling the result, and a built-in tightening counter supports batch fastening and go / no-go control on the line.

The screwdriver stores 800 readings and supports real-time output approximately every 1/160 s in C mode. It is cordless and battery powered, with an LCD 4-digit display and CW / CCW measurement. For help choosing between the DID-4 and the DID-05, please contact our engineers.

Key Features

Typical Applications

Electric tightening and torque verification of small and medium torque screws, especially batch fastening with count control and pass / fail judgement on assembly lines.

Model Selection & Reference Figures

The DID-4 and the DID-05 are two capacity variants of the same series: the DID-4 covers 0.020–4 N·m with a HEX 6.35 mm bit holder, while the DID-05 covers 2.0–500.0 mN·m with a φ4 mm holder. Display, judgement, counting and data functions are identical, so choose by tightening torque. Standard accessories: cross bits ○+ #1 and #2, bit holder, one-way bit holder, dedicated charger (input AC100V–230V 50/60Hz), inspection certificate, calibration certificate and traceability chart. Data output requires an optional USB cable (mini-B type). State "CEDAR (Sugisaki Meter) + model" when ordering, for example CEDAR DID-4.

Frequently Asked Questions

Q: What is the measuring range?
A: 0.020–4 N·m, accuracy ±0.5% (±0.003 N·m below 0.499 N·m), with a HEX 6.35 mm bit holder.

Q: Can ordinary hex bits be used, and what is the battery life?
A: Yes, standard 6.35 mm hex bits fit. The Ni-MH pack is 1.2V × 4 cells (800 mAh), charging in about 3 hours for up to 12 hours of use, with auto power-off after 10 minutes idle.

Q: What is supplied with the instrument?
A: Cross bits ○+ #1 and #2, bit holder, one-way bit holder, dedicated charger (input AC100V–230V 50/60Hz), and the inspection certificate, calibration certificate and traceability chart.

Service & Support

Guangzhou Yunke Electronic Co., Ltd. supplies the CEDAR DID series with selection advice, quotations, demonstrations, bits, USB cables and after-sales support.

Specification Sources

Values above are taken item by item from the official Sugisaki Meter (CEDAR) DID-4 specification PDF (the official specification table) and product page, with no unit conversions or inferred values; items shown as "-" or absent from the official table are likewise left blank. This is a quotation-only catalogue and no prices are listed.

For a quotation, lead time or a demonstration, please contact our engineers.

Related Products

CEDAR DI-12-SL02 Torque Testers
Torque Testers

CEDAR DI-12-SL02 Torque Testers

DI-12-SL02
└ CEDAR (Japan)
CEDAR DI-12-SL4 Torque Testers
Torque Testers

CEDAR DI-12-SL4 Torque Testers

DI-12-SL4
└ CEDAR (Japan)
CEDAR CP-10 Torque Testers
Torque Testers

CEDAR CP-10 Torque Testers

CP-10
└ CEDAR (Japan)
CEDAR CP-1 Torque Testers
Torque Testers

CEDAR CP-1 Torque Testers

CP-1
└ CEDAR (Japan)
CEDAR NTS7-RT2 Torque Testers
Torque Testers

CEDAR NTS7-RT2 Torque Testers

NTS7-RT2
└ CEDAR (Japan)
CEDAR NTS7-RT05 Torque Testers
Torque Testers

CEDAR NTS7-RT05 Torque Testers

NTS7-RT05
└ CEDAR (Japan)