CEDAR DIW-75 Torque Testers (Model DIW-75) is a Torque Testers supplied by Guangzhou Yunke Electronics Co., Ltd. CEDAR DIW-75 Torque Testers — Torque Testers · Yunke Electronics. Request a quotation and datasheet.
Brand: CEDAR | Category: Torque Testers
Sales Inquiries: 15626018696 · 78403603@qq.com

| Measurement Range | 0.20~75 N·m |
|---|---|
| Accuracy ( to Value Lower Limit) | ±0.5% |
| Base Interface | □9.5 Head |
| Dimensions | 320×φ34 mm(Grip Diameter) |
| Weight | Approx. 620 g |
| Accuracy | ±0.5% |
| Display | LCD 4 Digits digits Display |
| Measuring Direction | CW-CCW(Right · Left Direction) |
| Measurement Mode | PP(Peak): Hold Load Maximum Value; TR(): with Load Real-time Display; PD(Peak under ): Hold Load by above to under ; C(Real-time Output): Approx. per 1 / 160 s Output and |
| Upper Lower Limit Setting | above · Lower Limit Value can at Measuring Range internal Setting, up to 5 groups |
| Pass/Fail Judgment Function | per Setting Range Judgment (P-P Mode when); GOOD Lamp /NG Lamp |
| Maximum · Minimum · Average | Display Memory Data pcs Number, Maximum, Minimum, Average |
| Data Storage | Measured values Data 800 records; Data pcs Number · Maximum · Minimum · Average 10 ch |
| Data output | ASCII division Type (Baud Rate 19200); Output when requires with USB Wire ( B Type) |
| Auto Zero Time | 0.1~3.0 s (0.5 s Interval) Auto Zero; 0.0 s Setting is Manual Zero Setting |
| Key Zero Setting | Measuring Mode under can a Key Zero Setting Adjustment |
| Counting Setting | 1~99 times (per Direction Counting) |
| Power Supply | NiMH Battery 1.2V×4 cells (800 mAh) |
| Charging Time / Operating Time | Charging Approx. 3 hours / Maximum Charging when Continuous 12 hours Operating |
| Auto Power-off | 10 minutes No Operation Rear Power Supply OFF |
| Standard accessories | Single toward Sleeve (DIW-15 / 20 / 75)/ Ratchet Sleeve (DIW-120); Dedicated Charger; Check , Calibration Certificate, can Property Body Series Diagram |
| Part | Data Output requires with USB Wire ( B Type) |
Some specification lines are quoted from the original manufacturer datasheet. Numbers, units and model codes are preserved verbatim; an English datasheet is available on request.
DIW series is CEDARSpunnersShow one-digit twister wrenchCharliethe wrench's head can rotate about 300° to allow for reading angles to be adjusted in a narrow space. Supports upper and lower limit setting (up to 5 group) and the bee-beep/ LED qualified, built-in tight counter, data storage 800 bar and can pass USB (mini-B), (a) A cable-sales output, which is used to tighten records and trace them. Reference: 120 N·m, 0.20
The torque applicable to the bolt screws is confirmed when it is stung and stung and is often used to assemble the torque management and record-keeping of the assembly line
The wrench can rotate around the head about 300°
Show one, lightly compactChannel
Data Storage 800 bar
Data Output is a USB Shape Interface
Sets the top and bottom limit to torque%1%2%2
Set value with beeper and LED hint
Built-in tight count%
Charged battery drive
Auto turn off. Operation rest
Support real-time data output%2%2%2
The above parameters are itemized from the "se" table and the "supplier" of the official product specification PDF, which is not converted in units and is not extrapolated; This page is also not filled in for items that are not listed in the official specification form in the form "- ". Reference: CEDARDIW-75) the series is DIW-15/DIW-20/DIW-75/DIW-120, and the difference item for other models in the series is shown separately in that model entry
The wrench's head is rotated relative to the body300°the display screen can be moved to an observable angle from the inside, on-the-ground or in-back position of the equipment to reduce the error caused by difficulty in reading; the one-size design is shown to remove the cable drag from the external monitor
Top and bottom limit values can be set in the range of measurements and can be saved at mostGroup 5.Step & & & QuestSP-P is determined in the defined range, with a green light for GOOD/NG red light hint, supported by a beeper. The built-in buttons set 1-99 times, counting in a tight direction. The data is stored as "Specific value 800 bar + Data Number Max Minimum Mean value 10 ch"
DIW-15 for 0.20 15 N·m (Standard) DIW-20 for 0.20 20 N·m (9.5 common head), DIW-75 for 0.20 75 N·m,SpSpreaksS ZZZZ DIW-120 is 2.0 120 N·m ( 12.7 common head). It is recommended that the usual torque be left in the process in 1/3 — 2/3. Reference: 6.35
Please indicate "CEDAR (CEDAR meter)+ model" when ordering, for exampleScretsScCEDAR DIW-75The official pricing is not included on this page. Please contact Guangzhou Yunke Electronics Co., Ltd. for the price.Tppppp
Q: How do you choose the four large?!?
A: Selection of DIW-15 (0.20 — 15 N·m, □ 6.35), DIW-20 (0.20 — 20 N·m), □ 9.5, DIW-75 (0.20 — 75 N·m), DIW-120 (2.0 — 120 N·m, 12.7). The errors were 0.5 per cent
Q: Can you turn your head?!
A: Yes, the wrench's head can rotate around 300° relative to its body, which allows for reading the display in a narrow space
Q: Can data be exported?
A: Yes. Data are exported in ASCII format (Portrate 19200), with a separate USB line (mini-B); this machine store measuring value 800
Q: What are the annexes?
A: Randomly attached single-way cylinders (DIW-120 for thorns), specialized chargers and check-out reports, calibration certificates, traceability charts
All model codes, numbers and units are preserved verbatim from the original manufacturer datasheet. An English datasheet is available on request.
For a quotation, lead time or an optional calibration certificate, please contact our engineers.